Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows) > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Master Switch 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver door power window auto switch signal / ON or OFF
    ON: Driver door power window auto switch being operated
    OFF: Driver door power window auto switch not being operated
    -
    P Door P/W Auto SW
    Front passenger door power window auto up and down switch signal / ON or OFF
    ON: Front passenger door power window auto switch being operated
    OFF: Front passenger door power window auto switch not being operated
    -
    RR Door P/W Auto SW
    Rear RH door power window auto up and down switch signal / ON or OFF
    ON: Rear RH power window auto switch being operated
    OFF: Rear RH power window auto switch not being operated
    -
    RL Door P/W Auto SW
    Rear LH door power window auto up and down switch signal / ON or OFF
    ON: Rear LH power window auto switch being operated
    OFF: Rear LH power window auto switch not being operated
    -
    P Door P/W Up SW
    Front passenger door power window manual up switch signal / ON or OFF
    ON: Front passenger door power window manual up switch being operated
    OFF: Front passenger door power window manual up switch not being operated
    -
    RR Door P/W up switch
    Rear RH door power window manual up switch signal / ON or OFF
    ON: Rear RH power window manual up switch being operated
    OFF: Rear RH power window manual up switch not being operated
    -
    RL Door P/W up switch
    Rear LH door power window manual up switch signal / ON or OFF
    ON: Rear LH power window manual up switch being operated
    OFF: Rear LH power window manual up switch not being operated
    -
    P Door P/W Down SW
    Front passenger door power window manual down switch signal / ON or OFF
    ON: Front passenger door power window manual down switch being operated
    OFF: Front passenger door power window manual down switch not being operated
    -
    RR Door P/W Down SW
    Rear RH door power window manual down switch signal / ON or OFF
    ON: Rear RH power window manual down switch being operated
    OFF: Rear RH power window manual down switch not being operated
    -
    RL Door P/W Down SW
    Rear LH door power window manual down switch signal / ON or OFF
    ON: Rear LH power window manual down switch being operated
    OFF: Rear LH power window manual down switch not being operated
    -
    Window Lock Switch Status
    Window lock switch signal / ON or OFF
    ON: Window lock switch LOCK position
    OFF: Window lock switch UNLOCK position
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 or Max.: 255
    Number of DTCs will be displayed
    -

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Auto SW
    Driver door power window auto switch signal / ON or OFF
    ON: Driver door power window auto switch being operated
    OFF: Driver door power window auto switch not being operated
    -
    D Door P/W Up SW
    Driver door power window manual up switch signal / ON or OFF
    ON: Driver door power window manual up switch being operated
    OFF: Driver door power window manual up switch not being operated
    -
    D Door P/W Down SW
    Driver door power window manual down switch signal / ON or OFF
    ON: Driver door power window manual down switch being operated
    OFF: Driver door power window manual down switch not being operated
    -
    Glass Position (Close - 1/4)
    Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (1/4 - 2/4)
    Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (2/4 - 3/4)
    Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (3/4 - Open)
    Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    D Window Auto Up*
    Auto up operation using the multiplex network master switch assembly / OFF or ON
    Customize setting displayed
    -
    D Window Auto Down*
    Auto down operation using the multiplex network master switch assembly / OFF or ON
    Customize setting displayed
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 or Max.: 255
    Number of DTCs will be displayed
    -

    1. *: for TMMR Made

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger door power window auto switch signal / ON or OFF
    ON: Front passenger door power window auto switch being operated
    OFF: Front passenger door power window auto switch not being operated
    -
    P Door P/W Up SW
    Front passenger door power window manual up switch signal / ON or OFF
    ON: Front passenger door power window manual up switch being operated
    OFF: Front passenger door power window manual up switch not being operated
    -
    P Door P/W Down SW
    Front passenger door power window manual down switch signal / ON or OFF
    ON: Front passenger door power window manual down switch being operated
    OFF: Front passenger door power window manual down switch not being operated
    -
    Glass Position (Close - 1/4)
    Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (1/4 - 2/4)
    Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (2/4 - 3/4)
    Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (3/4 - Open)
    Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    P Window Auto Up
    Auto up operation using the power window regulator switch assembly / OFF or ON
    Customize setting displayed
    -
    P Window Auto Up From Driver
    Remote auto up operation using the multiplex network master switch assembly / OFF or ON
    Customize setting displayed
    -
    P Window Auto Down*
    Auto down operation using the power window regulator switch assembly / OFF or ON
    Customize setting displayed
    -
    P Window Auto Down From Driver*
    Remote auto down operation using the multiplex network master switch assembly / OFF or ON
    Customize setting displayed
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 or Max.: 255
    Number of DTCs will be displayed
    -
    1. *: for TMMR Made

    RL-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Door P/W Auto SW
    Rear LH door power window auto switch signal / ON or OFF
    ON: Rear LH door power window auto switch being operated
    OFF: Rear LH door power window auto switch not being operated
    -
    RL Door P/W Up SW
    Rear LH door power window manual up switch signal / ON or OFF
    ON: Rear LH door power window manual up switch being operated
    OFF: Rear LH door power window manual up switch not being operated
    -
    RL Door P/W Down SW
    Rear LH door power window manual down switch signal / ON or OFF
    ON: Rear LH door power window manual down switch being operated
    OFF: Rear LH door power window manual down switch not being operated
    -
    Glass Position (Close - 1/4)
    Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (1/4 - 2/4)
    Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (2/4 - 3/4)
    Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (3/4 - Open)
    Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    RL Window Auto Up
    Auto up operation using the rear power window regulator switch assembly (for LH door) / OFF or ON
    Customize setting displayed
    -
    RL Window Auto Up From Driver
    Remote auto up operation using the multiplex network master switch assembly / OFF or ON
    Customize setting displayed
    -
    RL Window Auto Down*
    Auto down operation using the rear power window regulator switch assembly (for LH door) / OFF or ON
    Customize setting displayed
    -
    RL Window Auto Down From Driver*
    Remote auto down operation using the multiplex network master switch assembly / OFF or ON
    Customize setting displayed
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 or Max.: 255
    Number of DTCs will be displayed
    -
    1. *: for TMMR Made

    RR-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door P/W Auto SW
    Rear RH door power window auto switch signal / ON or OFF
    ON: Rear RH door power window auto switch being operated
    OFF: Rear RH door power window auto switch not being operated
    -
    RR Door P/W Up SW
    Rear RH door power window manual up switch signal / ON or OFF
    ON: Rear RH door power window manual up switch being operated
    OFF: Rear RH door power window manual up switch not being operated
    -
    RR Door P/W Down SW
    Rear RH door power window manual down switch signal / ON or OFF
    ON: Rear RH door power window manual down switch being operated
    OFF: Rear RH door power window manual down switch not being operated
    -
    Glass Position (Close - 1/4)
    Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (1/4 - 2/4)
    Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (2/4 - 3/4)
    Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    Glass Position (3/4 - Open)
    Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution
    OK: Normal manual up operation
    Caution: Jam detected in the specified range
    Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
    RR Window Auto Up
    Auto up operation using the rear power window regulator switch assembly (for RH door) / OFF or ON
    Customize setting displayed
    -
    RR Window Auto Up From Driver
    Remote auto up operation using the multiplex network master switch assembly / OFF or ON
    Customize setting displayed
    -
    RR Window Auto Down*
    Auto down operation using the rear power window regulator switch assembly (for RH door) / OFF or ON
    Customize setting displayed
    -
    RR Window Auto Down From Driver*
    Remote auto down operation using the multiplex network master switch assembly / OFF or ON
    Customize setting displayed
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 or Max.: 255
    Number of DTCs will be displayed
    -
    1. *: for TMMR Made

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Driver door door lock/unlock switch lock signal (key-linked lock switch) / ON or OFF
    ON: Driver door key cylinder turned to lock position
    OFF: Driver door key cylinder turned to unlock position
    -
    D Door Key SW-UL
    Driver door door lock/unlock switch unlock signal (key-linked unlock switch) / ON or OFF
    ON: Driver door key cylinder turned to unlock position
    OFF: Driver door key cylinder turned to lock position
    -
    FR Door Courtesy
    Front door courtesy switch RH signal / ON or OFF
    ON: Front door RH closed
    OFF: Front door RH open
    -
    FL Door Courtesy
    Front door courtesy switch LH signal / ON or OFF
    ON: Front door LH closed
    OFF: Front door LH open
    -
    Door Key P/W Up
    Door key linked power window up / ON or OFF
    Customization status displayed
    -
    Door Key P/W Down
    Door key linked power window down / ON or OFF
    Customization status displayed
    -
    P/W Up W/Transmit
    Wireless transmitter linked power window up / ON or OFF
    Customization status displayed
    -
    P/W Down W/Transmit
    Wireless transmitter linked power window down / ON or OFF
    Customization status displayed
    -
    P/W Wireless Ope Buzz
    Buzzer sounds of wireless power window / ON or OFF
    Customization status displayed
    -
    Communication D-Door Motor
    Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -
    Communication P-Door Motor
    Connection status between power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -
    Communication RR-Door Motor
    Connection status between power window regulator motor assembly (for rear RH) and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -
    Communication RL-Door Motor
    Connection status between power window regulator motor assembly (for rear LH) and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -
    Communication Master SW
    Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


    D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    RR-Door Motor (Power Window Regulator Motor Assembly (for Rear RH Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -