Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > TERMINALS OF ECU

for Preparation Click here



CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

B343031E08

  1. Disconnect the K12 connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K12-14 (BDR) - Body ground
    W - Body ground
    +B power supply
    Always
    11 to 14 V
    K12-6 (CPUB) - Body ground
    W - Body ground
    +B power supply
    Always
    11 to 14 V
    K12-5 (SIG) - Body ground
    GR - Body ground
    Ignition power supply
    Engine switch off → on (IG)
    0 V → 11 to 14 V
    K12-7 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the K12 connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    z18-1 (MV) - z18-9 (MH)
    V - BR
    Vertical mirror motor drive voltage
    LH mirror surface moving upward → stopped
    11 to 14 V → 0 V
    z18-10 (M+) - z18-1 (MV)
    R - V
    Vertical mirror motor drive voltage
    LH mirror surface moving downward → stopped
    11 to 14 V → 0 V
    z18-10 (M+) - z18-9 (MH)
    R - BR
    Horizontal mirror motor drive voltage
    LH mirror surface moving right → stopped
    11 to 14 V → 0 V
    z18-9 (MH) - z18-1 (MV)
    BR - V
    Horizontal mirror motor drive voltage
    LH mirror surface moving left → stopped
    11 to 14 V → 0 V
    z18-4 (HTR+) - z18-12 (HTR-)
    B - B
    Mirror heater relay drive voltage
    Rear defogger switch on
    11 to 14 V
    z18-5 (VDD) - z18-14 (GND)
    R-W - B-Y
    Mirror position sensor power supply
    Engine switch on (IG)
    4.55 to 5.45 V
    z18-6 (VSSR) - z18-14 (GND)
    L-W - B-Y
    Mirror position sensor signal
    Engine switch on (IG)
    0.96 to 4.04 V
    z18-13 (HSSR) - z18-14 (GND)
    O-W - B-Y
    Mirror position sensor signal
    Engine switch on (IG)
    0.96 to 4.04 V
    K12-3 (M2) - K12-13 (MSWE)
    G - B
    M2 switch signal for seat memory switch
    M2 switch on
    Below 1 V
    M2 switch off
    11 to 14 V
    K12-2 (M1) - K12-13 (MSWE)
    R - B
    M1 switch signal for seat memory switch
    M1 switch on
    Below 1 V
    M1 switch off
    11 to 14 V
    K12-1 (MM) - K12-13 (MSWE)
    P - B
    SET switch signal for seat memory switch
    SET switch on
    Below 1 V
    SET switch off
    11 to 14 V


CHECK OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

B343031E09

  1. Disconnect the J10 connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J10-14 (BDR) - Body ground
    GR - Body ground
    +B power supply
    Always
    11 to 14 V
    J10-6 (CPUB) - Body ground
    W - Body ground
    +B power supply
    Always
    11 to 14 V
    J10-5 (SIG) - Body ground
    BE - Body ground
    Ignition power supply
    Engine switch off → on (IG)
    0 V → 11 to 14 V
    J10-7 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the J10 connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    z17-1 (MV) - z17-9 (MH)
    V - BR
    Vertical mirror motor drive voltage
    RH mirror surface moving upward → stopped
    11 to 14 V → 0 V
    z17-10 (M+) - z17-1 (MV)
    R - V
    Vertical mirror motor drive voltage
    RH mirror surface moving downward → stopped
    11 to 14 V → 0 V
    z17-10 (M+) - z17-9 (MH)
    R - BR
    Horizontal mirror motor drive voltage
    RH mirror surface moving right → stopped
    11 to 14 V → 0 V
    z17-9 (MH) - z17-1 (MV)
    BR - V
    Horizontal mirror motor drive voltage
    RH mirror surface moving left → stopped
    11 to 14 V → 0 V
    z17-4 (HTR+) - z17-12 (HTR-)
    B - B
    Mirror heater relay drive voltage
    Rear defogger switch on
    11 to 14 V
    z17-5 (VDD) - z17-14 (GND)
    R-W - B-Y
    Mirror position sensor power supply
    Engine switch on (IG)
    4.55 to 5.45 V
    z17-6 (VSSR) - z17-14 (GND)
    L-W - B-Y
    Mirror position sensor signal
    Engine switch on (IG)
    0.96 to 4.04 V
    z17-13 (HSSR) - z17-14 (GND)
    O-W - B-Y
    Mirror position sensor signal
    Engine switch on (IG)
    0.96 to 4.04 V