Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > DATA LIST / ACTIVE TEST

for Preparation Click here



USING GTS
  1. Connect the GTS to the DLC3.

  2. Monitor the ECU data by following the prompts on the GTS screen.

    HINT:
    The GTS has a "Snapshot" function which records the monitored data. Refer to the GTS operator's manual for further details.


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Mirror L or Mirror R / Data List.

  5. Read the Data List according to the display on the GTS.

    Mirror L / Mirror R 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Seat Memory Switch1
    Seat memory switch M1 signal/ON or OFF
    ON: Seat memory switch M1 on
    OFF: Seat memory switch M1 off
    -
    Seat Memory Switch2
    Seat memory switch M2 signal/ON or OFF
    ON: Seat memory switch M2 on
    OFF: Seat memory switch M2 off
    -
    Seat Memory Switch3*
    Seat memory switch M3 signal/ON or OFF
    ON: Seat memory switch M3 on
    OFF: Seat memory switch M3 off
    Not applicable
    Seat Memory Set SW
    Seat memory switch SET signal/ON or OFF
    ON: Seat memory switch SET on
    OFF: Seat memory switch SET off
    -
    Mirror Memory No. 1
    Mirror position memorized in memory switch M1/OFF or ON
    ON: Memorized
    OFF: Not memorized
    -
    Mirror Memory No. 2
    Mirror position memorized in memory switch M2/OFF or ON
    ON: Memorized
    OFF: Not memorized
    -
    Mirror Memory No. 3*
    Mirror position memorized in memory switch M3/OFF or ON
    ON: Memorized
    OFF: Not memorized
    Not applicable
    Mirror Vertical Sensor Vol
    Vertical mirror position/MIN: 0, MAX: 4.98 V
    Within range from 0 to 4.98 V
    -
    Mirror Horizontal Sensor Vol
    Horizontal mirror position/MIN: 0, MAX: 4.98 V
    Within range from 0 to 4.98 V
    -
    +B Voltage Input Value
    Power supply for outer mirror control ECU assembly/MIN: 0 V, MAX: 19.98 V
    Within range from 11 to 14 V
    -

    1. *: Although the item is displayed on the GTS, it is not applicable to this vehicle.

  6. Enter the following menus: Body Electrical / Main Body / Data List.

  7. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror Selection SW (R)
    Mirror select switch signal for RH mirror / ON or OFF
    ON: Mirror select switch in R position
    OFF: Mirror select switch off or in L position
    -
    Mirror Selection SW (L)
    Mirror select switch signal for LH mirror / ON or OFF
    ON: Mirror select switch in L position
    OFF: Mirror select switch off or in R position
    -
    Mirror Position SW (R)
    Mirror adjust switch signal (Right) / ON or OFF
    ON: Mirror adjust switch pressed right
    OFF: Mirror adjust switch not pressed right
    Check with the mirror select switch in any position except neutral
    Mirror Position SW (L)
    Mirror adjust switch signal (Left) / ON or OFF
    ON: Mirror adjust switch pressed left
    OFF: Mirror adjust switch not pressed left
    Check with the mirror select switch in any position except neutral
    Mirror Position SW (Up)
    Mirror adjust switch signal (Up) / ON or OFF
    ON: Mirror adjust switch pressed up
    OFF: Mirror adjust switch not pressed up
    Check with the mirror select switch in any position except neutral
    Mirror Position SW (Dwn)
    Mirror adjust switch signal (Down) / ON or OFF
    ON: Mirror adjust switch pressed down
    OFF: Mirror adjust switch not pressed down
    Check with the mirror select switch in any position except neutral
    Outer Mirror Fold SW
    Retractable outer mirror switch signal / ON or OFF
    ON: Retractable outer mirror switch in retract position
    OFF: Retractable outer mirror switch in driving position
    -
    Mem SW No. w/KeyID1
    Switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID1
    MEM SW1: M1 linked with key ID1
    MEM SW2: M2 linked with key ID1
    MEM SW3: M3 linked with key ID1*
    -
    Mem SW No. w/KeyID2
    Switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID2
    MEM SW1: M1 linked with key ID2
    MEM SW2: M2 linked with key ID2
    MEM SW3: M3 linked with key ID2*
    -
    Mem SW No. w/KeyID3
    Switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID3
    MEM SW1: M1 linked with key ID3
    MEM SW2: M2 linked with key ID3
    MEM SW3: M3 linked with key ID3*
    -
    Mem SW No. w/KeyID4
    Switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID4
    MEM SW1: M1 linked with key ID4
    MEM SW2: M2 linked with key ID4
    MEM SW3: M3 linked with key ID4*
    -
    Mem SW No. w/KeyID5
    Switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID5
    MEM SW1: M1 linked with key ID5
    MEM SW2: M2 linked with key ID5
    MEM SW3: M3 linked with key ID5*
    -
    Mem SW No. w/KeyID6
    Switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID6
    MEM SW1: M1 linked with key ID6
    MEM SW2: M2 linked with key ID6
    MEM SW3: M3 linked with key ID6*
    -
    Mem SW No. w/KeyID7
    Switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID7
    MEM SW1: M1 linked with key ID7
    MEM SW2: M2 linked with key ID7
    MEM SW3: M3 linked with key ID7*
    -

    1. *: Although the item is displayed on the GTS, it is not applicable to this vehicle.


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Mirror L or Mirror R / Active Test.

  5. Perform the Active Test according to the display on the GTS.

    Mirror L / Mirror R 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Mirror Up/Down
    Mirror vertical operation
    Up / Down
    1. Operate with engine switch on (IG) and the vehicle stopped.
    2. This test activates the mirror up or down.
    3. This operation can be confirmed by watching the mirror move in the desired direction.
    Mirror Right/Left
    Mirror horizontal operation
    Right / Left
    1. Operate with engine switch on (IG) and the vehicle stopped.
    2. This test tilts the mirror right or left.
    3. This operation can be confirmed by watching the mirror move in the desired direction.
    Mirror Fold/Return
    Mirror retract operation
    Fold / Return
    1. Operate with engine switch on (IG) and the vehicle stopped.
    2. This test activates the Fold / Return.
    3. This operation can be confirmed by watching the mirror move in the desired direction.
    Mirror Heater
    Mirror heater operation
    ON / OFF
    1. Operate with engine switch on (IG) and the vehicle stopped.
    2. This test activates the mirror heater on or off.
    3. Mirror heater operation can be confirmed by touch.

  6. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  7. Perform the Active Test according to the display on the GTS.

    Driver Seat 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Defogger Relay (Rear)
    Mirror Heater
    ON or OFF
    -