Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM


E313899E03


INSPECTION PROCEDURE

NOTICE:
  1. The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).
  2. Inspect the fuse for circuits related to this system before performing the following inspection procedure.

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver assembly, steering pad switch, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

    Result:

    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except radio receiver assembly.
    B
    No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.).
    C



B
Go to step 5

C
GO TO LIGHTING SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
  1. Disconnect the I28 spiral cable with sensor sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I28-13 (IL+2) - Body ground
    Light control switch in tail or head position
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH
  1. Remove the steering pad switch assembly (Click here).



  1. Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.


    E314834E02

  1. Check that the switch illumination illuminates.

    OK:
    The steering pad switch illumination illuminates.


Text in Illustration 
*a
Component without harness connected
(Steering Pad Switch Assembly)
-
-


NG
REPLACE STEERING PAD SWITCH (Click here)
OK


4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
  1. Remove the spiral cable with sensor sub-assembly (Click here).



    E226306E35
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-5 (IL+2) - I28-13 (IL+2)
    Center
    3 Ω or less
    2.5 rotations to the left
    2.5 rotations to the right
    z3-8 (EAU) - I28-3 (EAU)
    Center
    3 Ω or less
    2.5 rotations to the left
    2.5 rotations to the right

  1. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-5 (IL+2) - I28-13 (IL+2)
    Always
    3 Ω or less
    z3-8 (EAU) - I28-3 (EAU)
    Always
    3 Ω or less

    NOTICE:
    1. Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.
    2. The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying.
    3. As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.

    Text in Illustration 
    *a
    Component without harness connected
    (spiral cable with sensor sub-assembly)
    *b
    Steering Pad Switch Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - RADIO RECEIVER ASSEMBLY - BODY GROUND) 

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
  1. Disconnect the I148 radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I148-10 (ILL+) - Body ground
    Light control switch in tail or head position
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)