Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.
Therefore, the radio receiver assembly cannot be operated using the steering pad switch, and also the radio receiver assembly itself cannot function.

WIRING DIAGRAM


E309796E02


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
  1. Disconnect the I150 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I150-21 (SW1) - I150-23 (SWG)
    No switch pushed
    95 to 105 kΩ
    Up switch pushed
    Below 2.5 Ω
    Down switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    I150-22 (SW2) - I150-23 (SWG)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH
  1. Remove the steering pad switch assembly (Click here).



  1. Measure the resistance according to the value(s) in the table below.


    E314833E02


    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    11 (AU1) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Up switch pushed
    Below 2.5 Ω
    Down switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    10 (AU2) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch)
    *b
    Volume+
    *c
    Volume-
    *d
    Down
    *e
    Up
    *f
    MODE/HOLD



NG
REPLACE STEERING PAD SWITCH (Click here)
OK


3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
  1. Remove the spiral cable with sensor sub-assembly (Click here).



    E226306E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-8 (EAU) - I28-3 (EAU)
    Center
    3 Ω or less
    2.5 rotations to the left
    2.5 rotations to the right
    z3-11 (AU1) - I28-6 (AU1)
    Center
    3 Ω or less
    2.5 rotations to the left
    2.5 rotations to the right
    z3-10 (AU2) - I28-5 (AU2)
    Center
    3 Ω or less
    2.5 rotations to the left
    2.5 rotations to the right

  1. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-8 (EAU) - I28-3 (EAU)
    Always
    3 Ω or less
    z3-11 (AU1) - I28-6 (AU1)
    Always
    3 Ω or less
    z3-10 (AU2) - I28-5 (AU2)
    Always
    3 Ω or less

    NOTICE:
    1. Press and hold the lock located in the center of the spiral cable with sensor sub-assembly to rotate the spiral cable with sensor sub-assembly.
    2. The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
    3. As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.

    Text in Illustration 
    *a
    Component without harness connected
    (spiral cable with sensor sub-assembly)
    *b
    Steering Pad Switch Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)