Home › Drivetrain ยท AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT (for TMC, TMMR Made)

REAR AXLE HUB BOLT (for TMC, TMMR Made) > REPLACEMENT

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. REMOVE REAR WHEEL


2. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    C083014
  1. Remove the bolt and separate the rear flexible hose from the rear shock absorber assembly.

  1. Remove the 2 bolts, and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging down by the rear flexible hose.



3. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Remove the parking brake shoe adjusting hole plug.



4. REMOVE REAR DISC


    C238505E01
  1. Put matchmarks on the rear disc and the rear axle hub.
    Text in Illustration 
    *a
    Matchmark



    C201774
  1. Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.



5. REMOVE REAR AXLE HUB BOLT


    C240540E01
  1. Temporarily install 2 nuts to the rear axle hub bolts as shown in the illustration.
    Text in Illustration 
    *1
    Nut

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    NOTICE:
    Install the nuts to prevent damage to the rear axle hub bolts.

  1. Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

    SST
    09611-12010  

    NOTICE:
    Do not damage the threads of the rear axle hub bolts.



6. INSTALL REAR AXLE HUB BOLT


    C240541E08
  1. Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.
    Text in Illustration 
    *1
    Nut
    *2
    Washer

  1. Install a washer and nut to the rear axle hub bolt as shown in the illustration.

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    HINT:
    Recommended washer thickness is 5 mm (0.197 in.) or more.

  1. Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the nut.

    NOTICE:
    1. Install the nuts to prevent damage to the rear axle hub bolts.
    2. Do not damage the threads of the rear axle hub bolts.

  1. Remove the 3 nuts and washer from the 3 rear axle hub bolts.



7. INSTALL REAR DISC


    C238505E01
  1. Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



8. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Install the parking brake shoe adjusting hole plug.



9. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
  1. Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    62 N*m{ 630 kgf*cm , 46 ft.*lbf }

  1. Install the rear flexible hose to the rear shock absorber assembly with the bolt.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }



10. ADJUST PARKING BRAKE
(Click here)


11. INSTALL REAR WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }