POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows) > TERMINALS OF ECU |
| MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
Disconnect the K3*1 or J3*2 multiplex network master switch assembly connector.

| *A | for LHD | *B | for RHD |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K3-11 (B) - K3-12 (GND) | W - BR | Power supply | Always | 11 to 14 V |
| K3-12 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J3-11 (B) - J3-12 (GND) | W - BR | Power supply | Always | 11 to 14 V |
| J3-12 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the K3*1 or J3*2 multiplex network master switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K3-15 (DOWN) - K3-12 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, driver door power window regulator switch not pushed or pulled | 11 to 14 V |
| K3-15 (DOWN) - K3-12 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) | Below 1 V |
| K3-18 (LED) - K3-12 (GND) | Y - BR | LED illumination signal | Ignition switch ON | 11 to 14 V |
| K3-18 (LED) - K3-12 (GND) | Y - BR | LED illumination signal | Ignition switch off | Below 1 V |
| K3-20 (UP) - K3-12 (GND) | G - BR | Power window motor UP output | Ignition switch ON, driver door power window regulator switch not pushed or pulled | 11 to 14 V |
| K3-20 (UP) - K3-12 (GND) | G - BR | Power window motor UP output | Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) | Below 1 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J3-15 (DOWN) - J3-12 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, driver door power window regulator switch not pushed or pulled | 11 to 14 V |
| J3-15 (DOWN) - J3-12 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) | Below 1 V |
| J3-18 (LED) - J3-12 (GND) | Y - BR | LED illumination signal | Ignition switch ON | 11 to 14 V |
| J3-18 (LED) - J3-12 (GND) | Y - BR | LED illumination signal | Ignition switch off | Below 1 V |
| J3-20 (UP) - J3-12 (GND) | G - BR | Power window motor UP output | Ignition switch ON, driver door power window regulator switch not pushed or pulled | 11 to 14 V |
| J3-20 (UP) - J3-12 (GND) | G - BR | Power window motor UP output | Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) | Below 1 V |
| CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY |
Disconnect the J4*1 or K4*2 power window regulator switch assembly connector.

| *A | for LHD | *B | for RHD |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J4-1 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K4-1 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the J4*1 or K4*2 power window regulator switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J4-4 (LED) - J4-1 (GND) | Y - BR | LED illumination signal | Ignition switch ON | 11 to 14 V |
| J4-4 (LED) - J4-1 (GND) | Y - BR | LED illumination signal | Ignition switch off | Below 1 V |
| J4-6 (UP) - J4-1 (GND) | BE - BR | Power window motor UP output | Ignition switch ON, power window regulator switch assembly not pushed or pulled | 11 to 14 V |
| J4-6 (UP) - J4-1 (GND) | BE - BR | Power window motor UP output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) | Below 1 V |
| J4-6 (UP) - J4-1 (GND) | BE - BR | Power window motor UP output | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| J4-6 (UP) - J4-1 (GND) | BE - BR | Power window motor UP output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| J4-6 (UP) - J4-1 (GND) | BE - BR | Power window motor UP output | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| J4-7 (DOWN) - J4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, power window regulator switch assembly not pushed or pulled | 11 to 14 V |
| J4-7 (DOWN) - J4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) | Below 1 V |
| J4-7 (DOWN) - J4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| J4-7 (DOWN) - J4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| J4-7 (DOWN) - J4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| J4-8 (AUTO) - J4-1 (GND) | L - BR | Power window motor AUTO UP output | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| J4-8 (AUTO) - J4-1 (GND) | L - BR | Power window motor AUTO UP output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| J4-8 (AUTO) - J4-1 (GND) | L - BR | Power window motor AUTO UP output | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| J4-8 (AUTO) - J4-1 (GND) | L - BR | Power window motor AUTO DOWN output | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| J4-8 (AUTO) - J4-1 (GND) | L - BR | Power window motor AUTO DOWN output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| J4-8 (AUTO) - J4-1 (GND) | L - BR | Power window motor AUTO DOWN output | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K4-4 (LED) - K4-1 (GND) | Y - BR | LED illumination signal | Ignition switch ON | 11 to 14 V |
| K4-4 (LED) - K4-1 (GND) | Y - BR | LED illumination signal | Ignition switch off | Below 1 V |
| K4-6 (UP) - K4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, power window regulator switch assembly not pushed or pulled | 11 to 14 V |
| K4-6 (UP) - K4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) | Below 1 V |
| K4-6 (UP) - K4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| K4-6 (UP) - K4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| K4-6 (UP) - K4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| K4-7 (DOWN) - K4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, power window regulator switch assembly not pushed or pulled | 11 to 14 V |
| K4-7 (DOWN) - K4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) | Below 1 V |
| K4-7 (DOWN) - K4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| K4-7 (DOWN) - K4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| K4-7 (DOWN) - K4-1 (GND) | V - BR | Power window motor DOWN output | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| K4-8 (AUTO) - K4-1 (GND) | L - BR | Power window motor AUTO UP output | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| K4-8 (AUTO) - K4-1 (GND) | L - BR | Power window motor AUTO UP output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| K4-8 (AUTO) - K4-1 (GND) | L - BR | Power window motor AUTO UP output | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| K4-8 (AUTO) - K4-1 (GND) | L - BR | Power window motor AUTO DOWN output | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| K4-8 (AUTO) - K4-1 (GND) | L - BR | Power window motor AUTO DOWN output | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| K4-8 (AUTO) - K4-1 (GND) | L - BR | Power window motor AUTO DOWN output | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door) |
Disconnect the M4 rear power window regulator switch assembly (for LH door) connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| M4-1 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the M4 rear power window regulator switch assembly (for LH door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| M4-4 (LED) - M4-1 (GND) | LG - BR | LED illumination signal | Ignition switch ON | 11 to 14 V |
| M4-4 (LED) - M4-1 (GND) | LG - BR | LED illumination signal | Ignition switch off | Below 1 V |
| M4-6 (UP) - M4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or pulled | 11 to 14 V |
| M4-6 (UP) - M4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) | Below 1 V |
| M4-6 (UP) - M4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear LH door power window fully open | 11 to 14 V |
| M4-6 (UP) - M4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) | Below 1 V |
| M4-6 (UP) - M4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear LH door power window fully closed | 11 to 14 V |
| M4-7 (DOWN) - M4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or pulled | 11 to 14 V |
| M4-7 (DOWN) - M4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) | Below 1 V |
| M4-7 (DOWN) - M4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear LH door power window fully closed | 11 to 14 V |
| M4-7 (DOWN) - M4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) | Below 1 V |
| M4-7 (DOWN) - M4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear LH door power window fully open | 11 to 14 V |
| M4-8 (AUTO) - M4-1 (GND) | B - BR | Power window motor AUTO UP output | Ignition switch ON, rear LH door power window fully open | 11 to 14 V |
| M4-8 (AUTO) - M4-1 (GND) | B - BR | Power window motor AUTO UP output | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) | Below 1 V |
| M4-8 (AUTO) - M4-1 (GND) | B - BR | Power window motor AUTO UP output | Ignition switch ON, rear LH door power window fully closed | 11 to 14 V |
| M4-8 (AUTO) - M4-1 (GND) | B - BR | Power window motor AUTO DOWN output | Ignition switch ON, rear LH door power window fully closed | 11 to 14 V |
| M4-8 (AUTO) - M4-1 (GND) | B - BR | Power window motor AUTO DOWN output | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) | Below 1 V |
| M4-8 (AUTO) - M4-1 (GND) | B - BR | Power window motor AUTO DOWN output | Ignition switch ON, rear LH door power window fully open | 11 to 14 V |
| CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) |
Disconnect the L4 rear power window regulator switch assembly (for RH door) connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L4-1 (GND) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the L4 rear power window regulator switch assembly (for RH door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L4-4 (LED) - L4-1 (GND) | LG - BR | LED illumination signal | Ignition switch ON | 11 to 14 V |
| L4-4 (LED) - L4-1 (GND) | LG - BR | LED illumination signal | Ignition switch off | Below 1 V |
| L4-6 (UP) - L4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or pulled | 11 to 14 V |
| L4-6 (UP) - L4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) | Below 1 V |
| L4-6 (UP) - L4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear RH door power window fully open | 11 to 14 V |
| L4-6 (UP) - L4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) | Below 1 V |
| L4-6 (UP) - L4-1 (GND) | G - BR | Power window motor UP output | Ignition switch ON, rear RH door power window fully closed | 11 to 14 V |
| L4-7 (DOWN) - L4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or pulled | 11 to 14 V |
| L4-7 (DOWN) - L4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) | Below 1 V |
| L4-7 (DOWN) - L4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear RH door power window fully closed | 11 to 14 V |
| L4-7 (DOWN) - L4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) | Below 1 V |
| L4-7 (DOWN) - L4-1 (GND) | R - BR | Power window motor DOWN output | Ignition switch ON, rear RH door power window fully open | 11 to 14 V |
| L4-8 (AUTO) - L4-1 (GND) | B - BR | Power window motor AUTO UP output | Ignition switch ON, rear RH door power window fully open | 11 to 14 V |
| L4-8 (AUTO) - L4-1 (GND) | B - BR | Power window motor AUTO UP output | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) | Below 1 V |
| L4-8 (AUTO) - L4-1 (GND) | B - BR | Power window motor AUTO UP output | Ignition switch ON, rear RH door power window fully closed | 11 to 14 V |
| L4-8 (AUTO) - L4-1 (GND) | B - BR | Power window motor AUTO DOWN output | Ignition switch ON, rear RH door power window fully closed | 11 to 14 V |
| L4-8 (AUTO) - L4-1 (GND) | B - BR | Power window motor AUTO DOWN output | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) | Below 1 V |
| L4-8 (AUTO) - L4-1 (GND) | B - BR | Power window motor AUTO DOWN output | Ignition switch ON, rear RH door power window fully open | 11 to 14 V |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) |
Disconnect the K9*1 or J9*2 power window regulator motor assembly (for driver door) connector.

| *A | for LHD | *B | for RHD |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K9-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| K9-2 (B) - Body ground | GR - Body ground | Power supply | Always | 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J9-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| J9-2 (B) - Body ground | GR - Body ground | Power supply | Always | 11 to 14 V |
Reconnect the K9*1 or J9*2 power window regulator motor assembly (for driver door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K9-5 (LED) - K9-1 (GND) | Y - W-B | LED illumination signal | Ignition switch ON | 11 to 14 V |
| K9-5 (LED) - K9-1 (GND) | Y - W-B | LED illumination signal | Ignition switch off | Below 1 V |
| K9-7 (DOWN) - K9-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled | 11 to 14 V |
| K9-7 (DOWN) - K9-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) | Below 1 V |
| K9-7 (DOWN) - K9-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, driver door power window fully closed | 11 to 14 V |
| K9-7 (DOWN) - K9-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Automatic operation) | Below 1 V |
| K9-7 (DOWN) - K9-1 (GND) | R - W-B | Power window motor AUTO DOWN input | Ignition switch ON, driver door power window fully open | 11 to 14 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled | 11 to 14 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) | Below 1 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open | 11 to 14 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Automatic operation) | Below 1 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, driver door power window fully closed | 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J9-5 (LED) - J9-1 (GND) | Y - W-B | LED illumination signal | Ignition switch ON | 11 to 14 V |
| J9-5 (LED) - J9-1 (GND) | Y - W-B | LED illumination signal | Ignition switch off | Below 1 V |
| J9-7 (DOWN) - J9-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled | 11 to 14 V |
| J9-7 (DOWN) - J9-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) | Below 1 V |
| J9-7 (DOWN) - J9-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, driver door power window fully closed | 11 to 14 V |
| J9-7 (DOWN) - J9-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Automatic operation) | Below 1 V |
| J9-7 (DOWN) - J9-1 (GND) | R - W-B | Power window motor AUTO DOWN input | Ignition switch ON, driver door power window fully open | 11 to 14 V |
| J9-10 (UP) - J9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled | 11 to 14 V |
| J9-10 (UP) - J9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) | Below 1 V |
| J9-10 (UP) - J9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open | 11 to 14 V |
| J9-10 (UP) - J9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Automatic operation) | Below 1 V |
| J9-10 (UP) - J9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, driver door power window fully closed | 11 to 14 V |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door) |
Disconnect the J9*1 or K9*2 power window regulator motor assembly (for front passenger door) connector.

| *A | for LHD | *B | for RHD |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J9-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| J9-2 (B) - Body ground | GR - Body ground | Power supply | Always | 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K9-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| K9-2 (B) - Body ground | GR - Body ground | Power supply | Always | 11 to 14 V |
Reconnect the J9*1 or K9*2 power window regulator motor assembly (for front passenger door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J9-4 (AUTO) - J9-1 (GND) | L - W-B | Power window motor AUTO UP input | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| J9-4 (AUTO) - J9-1 (GND) | L - W-B | Power window motor AUTO UP input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| J9-4 (AUTO) - J9-1 (GND) | L - W-B | Power window motor AUTO UP input | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| J9-4 (AUTO) - J9-1 (GND) | L - W-B | Power window motor AUTO DOWN input | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| J9-4 (AUTO) - J9-1 (GND) | L - W-B | Power window motor AUTO DOWN input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| J9-4 (AUTO) - J9-1 (GND) | L - W-B | Power window motor AUTO DOWN input | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| J9-5 (LED) - J9-1 (GND) | Y - W-B | LED illumination signal | Ignition switch ON | 11 to 14 V |
| J9-5 (LED) - J9-1 (GND) | Y - W-B | LED illumination signal | Ignition switch off | Below 1 V |
| J9-7 (DOWN) - J9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, power window regulator switch assembly not pushed or pulled | 11 to 14 V |
| J9-7 (DOWN) - J9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) | Below 1 V |
| J9-7 (DOWN) - J9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| J9-7 (DOWN) - J9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| J9-7 (DOWN) - J9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| J9-10 (UP) - J9-1 (GND) | BE - W-B | Power window motor UP input | Ignition switch ON, power window regulator switch assembly not pushed or pulled | 11 to 14 V |
| J9-10 (UP) - J9-1 (GND) | BE - W-B | Power window motor UP input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) | Below 1 V |
| J9-10 (UP) - J9-1 (GND) | BE - W-B | Power window motor UP input | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| J9-10 (UP) - J9-1 (GND) | BE - W-B | Power window motor UP input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| J9-10 (UP) - J9-1 (GND) | BE - W-B | Power window motor UP input | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K9-4 (AUTO) - K9-1 (GND) | L - W-B | Power window motor AUTO UP input | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| K9-4 (AUTO) - K9-1 (GND) | L - W-B | Power window motor AUTO UP input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| K9-4 (AUTO) - K9-1 (GND) | L - W-B | Power window motor AUTO UP input | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| K9-4 (AUTO) - K9-1 (GND) | L - W-B | Power window motor AUTO DOWN input | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| K9-4 (AUTO) - K9-1 (GND) | L - W-B | Power window motor AUTO DOWN input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| K9-4 (AUTO) - K9-1 (GND) | L - W-B | Power window motor AUTO DOWN input | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| K9-5 (LED) - K9-1 (GND) | Y - W-B | LED illumination signal | Ignition switch ON | 11 to 14 V |
| K9-5 (LED) - K9-1 (GND) | Y - W-B | LED illumination signal | Ignition switch off | Below 1 V |
| K9-7 (DOWN) - K9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, power window regulator switch assembly not pushed or pulled | 11 to 14 V |
| K9-7 (DOWN) - K9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) | Below 1 V |
| K9-7 (DOWN) - K9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| K9-7 (DOWN) - K9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| K9-7 (DOWN) - K9-1 (GND) | V - W-B | Power window motor DOWN input | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, power window regulator switch assembly not pushed or pulled | 11 to 14 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) | Below 1 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, front passenger door power window fully open | 11 to 14 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| K9-10 (UP) - K9-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, front passenger door power window fully closed | 11 to 14 V |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door) |
Disconnect the M2 power window regulator motor assembly (for rear LH door) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| M2-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| M2-2 (B) - Body ground | G - Body ground | Power supply | Always | 11 to 14 V |
Reconnect the M2 power window regulator motor assembly (for rear LH door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| M2-4 (AUTO) - M2-1 (GND) | B - W-B | Power window motor AUTO UP input | Ignition switch ON, rear LH door power window fully open | 11 to 14 V |
| M2-4 (AUTO) - M2-1 (GND) | B - W-B | Power window motor AUTO UP input | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) | Below 1 V |
| M2-4 (AUTO) - M2-1 (GND) | B - W-B | Power window motor AUTO UP input | Ignition switch ON, rear LH door power window fully closed | 11 to 14 V |
| M2-4 (AUTO) - M2-1 (GND) | B - W-B | Power window motor AUTO DOWN input | Ignition switch ON, rear LH door power window fully closed | 11 to 14 V |
| M2-4 (AUTO) - M2-1 (GND) | B - W-B | Power window motor AUTO DOWN input | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) | Below 1 V |
| M2-4 (AUTO) - M2-1 (GND) | B - W-B | Power window motor AUTO DOWN input | Ignition switch ON, rear LH door power window fully open | 11 to 14 V |
| M2-5 (LED) - M2-1 (GND) | LG - W-B | LED illumination signal | Ignition switch ON | 11 to 14 V |
| M2-5 (LED) - M2-1 (GND) | LG - W-B | LED illumination signal | Ignition switch off | Below 1 V |
| M2-7 (DOWN) - M2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or pulled | 11 to 14 V |
| M2-7 (DOWN) - M2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) | Below 1 V |
| M2-7 (DOWN) - M2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear LH door power window fully closed | 11 to 14 V |
| M2-7 (DOWN) - M2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation) | Below 1 V |
| M2-7 (DOWN) - M2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear LH door power window fully open | 11 to 14 V |
| M2-10 (UP) - M2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or pulled | 11 to 14 V |
| M2-10 (UP) - M2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) | Below 1 V |
| M2-10 (UP) - M2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear LH door power window fully open | 11 to 14 V |
| M2-10 (UP) - M2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation) | Below 1 V |
| M2-10 (UP) - M2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear LH door power window fully closed | 11 to 14 V |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door) |
Disconnect the L2 power window regulator motor assembly (for rear RH door) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L2-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| L2-2 (B) - Body ground | G - Body ground | Power supply | Always | 11 to 14 V |
Reconnect the L2 power window regulator motor assembly (for rear RH door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L2-4 (AUTO) - L2-1 (GND) | B - W-B | Power window motor AUTO UP input | Ignition switch ON, rear RH door power window fully open | 11 to 14 V |
| L2-4 (AUTO) - L2-1 (GND) | B - W-B | Power window motor AUTO UP input | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) | Below 1 V |
| L2-4 (AUTO) - L2-1 (GND) | B - W-B | Power window motor AUTO UP input | Ignition switch ON, rear RH door power window fully closed | 11 to 14 V |
| L2-4 (AUTO) - L2-1 (GND) | B - W-B | Power window motor AUTO DOWN input | Ignition switch ON, rear RH door power window fully closed | 11 to 14 V |
| L2-4 (AUTO) - L2-1 (GND) | B - W-B | Power window motor AUTO DOWN input | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) | Below 1 V |
| L2-4 (AUTO) - L2-1 (GND) | B - W-B | Power window motor AUTO DOWN input | Ignition switch ON, rear RH door power window fully open | 11 to 14 V |
| L2-5 (LED) - L2-1 (GND) | LG - W-B | LED illumination signal | Ignition switch ON | 11 to 14 V |
| L2-5 (LED) - L2-1 (GND) | LG - W-B | LED illumination signal | Ignition switch off | Below 1 V |
| L2-7 (DOWN) - L2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or pulled | 11 to 14 V |
| L2-7 (DOWN) - L2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) | Below 1 V |
| L2-7 (DOWN) - L2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear RH door power window fully closed | 11 to 14 V |
| L2-7 (DOWN) - L2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation) | Below 1 V |
| L2-7 (DOWN) - L2-1 (GND) | R - W-B | Power window motor DOWN input | Ignition switch ON, rear RH door power window fully open | 11 to 14 V |
| L2-10 (UP) - L2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or pulled | 11 to 14 V |
| L2-10 (UP) - L2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) | Below 1 V |
| L2-10 (UP) - L2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear RH door power window fully open | 11 to 14 V |
| L2-10 (UP) - L2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation) | Below 1 V |
| L2-10 (UP) - L2-1 (GND) | G - W-B | Power window motor UP input | Ignition switch ON, rear RH door power window fully closed | 11 to 14 V |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
Disconnect the MB and I12 main body ECU (multiplex network body ECU) connector.

| *A | for LHD | *B | for RHD |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| MB-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-30 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| I12-3 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| MB-29 (ACC) - Body ground | - | ACC power supply | Ignition switch ACC | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Ignition switch off | Below 1 V |
| MB-31 (ALTB) - Body ground | - | Battery power supply | Ignition switch off | 11 to 14 V |
| MB-32 (IG) - Body ground | - | IG power supply | Ignition switch ON | 11 to 14 V |
| MB-32 (IG) - Body ground | - | IG power supply | Ignition switch off | Below 1 V |
Reconnect the MB and I12 main body ECU (multiplex network body ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| 3C-15 (FLCY) - Body ground | L - Body ground | Front door courtesy switch LH input | Front door LH open | Below 1 V |
| 3C-15 (FLCY) - Body ground | L - Body ground | Front door courtesy switch LH input | Front door LH closed | 11 to 14 V |
| I13-19 (FRCY) - Body ground | Y - Body ground | Front door courtesy switch RH input | Front door RH open | Below 1 V |
| I13-19 (FRCY) - Body ground | Y - Body ground | Front door courtesy switch RH input | Front door RH closed | 11 to 14 V |
| I13-11 (L2) - Body ground | R - Body ground | Driver door key-linked lock input | Driver door key cylinder turned to lock | Below 1 V |
| I13-11 (L2) - Body ground | R - Body ground | Driver door key-linked lock input | Driver door key cylinder off | Pulse generation |
| I13-24 (UL3) - Body ground | GR*1 - Body ground Y*2 - Body ground | Driver door key-linked unlock input | Driver door key cylinder turned to unlock | Below 1 V |
| I13-24 (UL3) - Body ground | GR*1 - Body ground Y*2 - Body ground | Driver door key-linked unlock input | Driver door key cylinder off | Pulse generation |
| I13-4 (PRG) - Body ground*3 | P - Body ground | Signal output to door control receiver | Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder | 11 to 14 V → Pulse generation → 11 to 14 V |
| I13-16 (RDA) - Body ground*3 | L - Body ground | Signal input from door control receiver | Ignition switch off, all doors closed and transmitter switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and transmitter switch pressed | Pulse generation |
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System) |
Disconnect the A43 certification ECU (smart key ECU assembly) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| A43-2 (+B) - Body ground | W - Body ground | +B power supply | Always | 11 to 14 V |
| A43-11 (E) - Body ground | W - Body ground | Ground | Always | Below 1 Ω |
Reconnect the A43 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| I78-5 (IG) - Body ground | LG - Body ground | IG power supply | Ignition switch off | Below 1 V |
| I78-5 (IG) - Body ground | LG - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| O1-5 (RCO) - A43-11 (E) | G - W | Door control receiver power source |
| Below 1 V |
| O1-5 (RCO) - A43-11 (E) | G - W | Door control receiver power source |
| 4.5 to 5.5 V |
| O1-17 (RDAM) - A43-11 (E) | Y - W | Door control receiver data input signal | Ignition switch off | Pulse between 11 to 14 V occurs regularly |