Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows) > TERMINALS OF ECU

for Preparation Click here



CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B164269E40

  1. Disconnect the K15 power window regulator master switch assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K15-3 (B) - K15-1 (GND)
    R - W-B
    Power supply
    Always
    11 to 14 V
    K15-13 (PWS) - K15-1 (GND)
    LG - W-B
    Power supply
    Engine switch on (IG)
    11 to 14 V
    K15-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the K15 power window regulator master switch assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K15-5 (DOWN) - K15-1 (GND)
    V - W-B
    Power window motor down output
    Engine switch on (IG), driver door power window regulator switch not pushed or pulled
    11 to 14 V
    K15-5 (DOWN) - K15-1 (GND)
    V - W-B
    Power window motor down output
    Engine switch on (IG), driver door power window moving, power window regulator master switch assembly pushed halfway down (Manual operation)
    Below 1 V
    K15-4 (UP) - K15-1 (GND)
    L - W-B
    Power window motor up output
    Engine switch on (IG), power window regulator master switch assembly not pushed or pulled
    11 to 14 V
    K15-4 (UP) - K15-1 (GND)
    L - W-B
    Power window motor up output
    Engine switch on (IG), driver door power window moving, power window regulator master switch assembly pulled halfway up (Manual operation)
    Below 1 V
    K15-12 (RLU) - K15-1 (GND)
    L - W-B
    Power window motor up output
    Engine switch on (IG), rear power window regulator switch assembly (for LH door) off
    Below 1 V
    K15-12 (RLU) - K15-1 (GND)
    L - W-B
    Power window motor up output
    Engine switch on (IG), rear power window regulator switch assembly (for LH door) up (Manual operation)
    11 to 14 V
    K15-15 (RLD) - K15-1 (GND)
    B - W-B
    Power window motor down output
    Engine switch on (IG), rear power window regulator switch assembly (for LH door) off
    Below 1 V
    K15-15 (RLD) - K15-1 (GND)
    B - W-B
    Power window motor down output
    Engine switch on (IG), rear power window regulator switch assembly (for LH door) down (Manual operation)
    11 to 14 V
    K15-10 (RRU) - K15-1 (GND)
    Y - W-B
    Power window motor up output
    Engine switch on (IG), rear power window regulator switch assembly (for RH door) off
    Below 1 V
    K15-10 (RRU) - K15-1 (GND)
    Y - W-B
    Power window motor up output
    Engine switch on (IG), rear power window regulator switch assembly (for RH door) up (Manual operation)
    11 to 14 V
    K15-16 (RRD) - K15-1 (GND)
    LG - W-B
    Power window motor down output
    Engine switch on (IG), rear power window regulator switch assembly (for RH door) off
    Below 1 V
    K15-16 (RRD) - K15-1 (GND)
    LG - W-B
    Power window motor down output
    Engine switch on (IG), rear power window regulator switch assembly (for RH door) down (Manual operation)
    11 to 14 V


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY

B351350E08

  1. Disconnect the J12 power window regulator switch assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J12-7 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the J12 power window regulator switch assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J12-2 (IG) - J12-7 (GND)
    R - W-B
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    J12-2 (IG) - J12-7 (GND)
    R - W-B
    IG power supply
    Engine switch off
    Below 1 V
    J12-5 (UP) - J12-7 (GND)
    L - W-B
    Power window motor up output
    Engine switch on (IG), power window regulator switch assembly not pushed or pulled
    11 to 14 V
    J12-5 (UP) - J12-7 (GND)
    L - W-B
    Power window motor up output
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation)
    Below 1 V
    J12-5 (UP) - J12-7 (GND)
    L - W-B
    Power window motor up output
    Engine switch on (IG), front passenger door power window fully open
    11 to 14 V
    J12-5 (UP) - J12-7 (GND)
    L - W-B
    Power window motor up output
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation)
    Below 1 V
    J12-5 (UP) - J12-7 (GND)
    L - W-B
    Power window motor up output
    Engine switch on (IG), front passenger door power window fully closed
    11 to 14 V
    J12-4 (DOWN) - J12-7 (GND)
    V - W-B
    Power window motor down output
    Engine switch on (IG), power window regulator switch assembly not pushed or pulled
    11 to 14 V
    J12-4 (DOWN) - J12-7 (GND)
    V - W-B
    Power window motor down output
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation)
    Below 1 V
    J12-4 (DOWN) - J12-7 (GND)
    V - W-B
    Power window motor down output
    Engine switch on (IG), front passenger door power window fully closed
    11 to 14 V
    J12-4 (DOWN) - J12-7 (GND)
    V - W-B
    Power window motor down output
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation)
    Below 1 V
    J12-4 (DOWN) - J12-7 (GND)
    V - W-B
    Power window motor down output
    Engine switch on (IG), front passenger door power window fully open
    11 to 14 V
    J12-8 (AUTO) - J12-7 (GND)
    Y - W-B
    Power window motor auto up output
    Engine switch on (IG), front passenger door power window fully open
    11 to 14 V
    J12-8 (AUTO) - J12-7 (GND)
    Y - W-B
    Power window motor auto up output
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation)
    Below 1 V
    J12-8 (AUTO) - J12-7 (GND)
    Y - W-B
    Power window motor auto up output
    Engine switch on (IG), front passenger door power window fully closed
    11 to 14 V
    J12-8 (AUTO) - J12-7 (GND)
    Y - W-B
    Power window motor auto down output
    Engine switch on (IG), front passenger door power window fully closed
    11 to 14 V
    J12-8 (AUTO) - J12-7 (GND)
    Y - W-B
    Power window motor auto down output
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation)
    Below 1 V
    J12-8 (AUTO) - J12-7 (GND)
    Y - W-B
    Power window motor auto down output
    Engine switch on (IG), front passenger door power window fully open
    11 to 14 V


CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR)

B351351E05

  1. Disconnect the M7 rear power window regulator switch assembly (for LH door) connector.

  2. Measure the voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M7-2 (B) - Body ground
    G - Body ground
    Power supply
    Engine switch on (IG)
    11 to 14 V

  3. Reconnect the M7 rear power window regulator switch assembly (for LH door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M7-7 (U) - Body ground
    B - Body ground
    Power window motor up output
    Engine switch on (IG), rear power window regulator switch assembly (for LH door) off
    Below 1 V
    M7-7 (U) - Body ground
    B - Body ground
    Power window motor up output
    Engine switch on (IG), rear power window regulator switch assembly (for LH door) up (Manual operation)
    11 to 14 V
    M7-1 (D) - Body ground
    R - Body ground
    Power window motor down output
    Engine switch on (IG), rear power window regulator switch assembly (for LH door) off
    Below 1 V
    M7-1 (D) - Body ground
    R - Body ground
    Power window motor down output
    Engine switch on (IG), rear power window regulator switch assembly (for LH door) down (Manual operation)
    11 to 14 V


CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)

B351351E06

  1. Disconnect the L7 rear power window regulator switch assembly (for RH door) connector.

  2. Measure the voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L7-2 (B) - Body ground
    G - Body ground
    Power supply
    Engine switch on (IG)
    11 to 14 V

  3. Reconnect the L7 rear power window regulator switch assembly (for RH door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L7-7 (U) - Body ground
    B - Body ground
    Power window motor up output
    Engine switch on (IG), rear power window regulator switch assembly (for RH door) off
    Below 1 V
    L7-7 (U) - Body ground
    B - Body ground
    Power window motor up output
    Engine switch on (IG), rear power window regulator switch assembly (for RH door) up (Manual operation)
    11 to 14 V
    L7-1 (D) - Body ground
    R - Body ground
    Power window motor down output
    Engine switch on (IG), rear power window regulator switch assembly (for RH door) off
    Below 1 V
    L7-1 (D) - Body ground
    R - Body ground
    Power window motor down output
    Engine switch on (IG), rear power window regulator switch assembly (for RH door) down (Manual operation)
    11 to 14 V


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

B280976E38

  1. Disconnect the K9 power window regulator motor assembly (for driver door) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    K9-2 (B) - Body ground
    W - Body ground
    Power supply
    Always
    11 to 14 V

  3. Reconnect the K9 power window regulator motor assembly (for driver door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), power window regulator master switch assembly not pushed or pulled
    11 to 14 V
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), driver door power window moving, power window regulator master switch assembly pushed halfway down (Manual operation)
    Below 1 V
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), driver door power window fully closed
    11 to 14 V
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), driver door power window moving, power window regulator master switch assembly fully pushed down (Auto operation)
    Below 1 V
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), driver door power window fully open
    11 to 14 V
    K9-10 (UP) - K9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), power window regulator master switch assembly not pushed or pulled
    11 to 14 V
    K9-10 (UP) - K9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), driver door power window moving, power window regulator master switch assembly pulled halfway up (Manual operation)
    Below 1 V
    K9-10 (UP) - K9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), power window regulator master switch assembly fully open
    11 to 14 V
    K9-10 (UP) - K9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), driver door power window moving, power window regulator master switch assembly fully pulled up (Auto operation)
    Below 1 V
    K9-10 (UP) - K9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), driver door power window fully closed
    11 to 14 V


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR)

B280976E41

  1. Disconnect the J9 power window regulator motor assembly (for front passenger door) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    J9-2 (B) - Body ground
    GR - Body ground
    Power supply
    Always
    11 to 14 V

  3. Reconnect the J9 power window regulator motor assembly (for front passenger door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-5 (IG) - J9-1 (GND)
    R - W-B
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    J9-5 (IG) - J9-1 (GND)
    R - W-B
    IG power supply
    Engine switch off
    Below 1 V
    J9-4 (AUTO) - J9-1 (GND)
    Y - W-B
    Power window motor auto up input
    Engine switch on (IG), front passenger door power window fully open
    11 to 14 V
    J9-4 (AUTO) - J9-1 (GND)
    Y - W-B
    Power window motor auto up input
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation)
    Below 1 V
    J9-4 (AUTO) - J9-1 (GND)
    Y - W-B
    Power window motor auto up input
    Engine switch on (IG), front passenger door power window fully closed
    11 to 14 V
    J9-4 (AUTO) - J9-1 (GND)
    Y - W-B
    Power window motor auto down input
    Engine switch on (IG), front passenger door power window fully closed
    11 to 14 V
    J9-4 (AUTO) - J9-1 (GND)
    Y - W-B
    Power window motor auto down input
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation)
    Below 1 V
    J9-4 (AUTO) - J9-1 (GND)
    Y - W-B
    Power window motor auto down input
    Engine switch on (IG), front passenger door power window fully open
    11 to 14 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), power window regulator switch assembly not pushed or pulled
    11 to 14 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation)
    Below 1 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), front passenger door power window fully closed
    11 to 14 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation)
    Below 1 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor down input
    Engine switch on (IG), front passenger door power window fully open
    11 to 14 V
    J9-10 (UP) - J9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), power window regulator switch assembly not pushed or pulled
    11 to 14 V
    J9-10 (UP) - J9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation)
    Below 1 V
    J9-10 (UP) - J9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), front passenger door power window fully open
    11 to 14 V
    J9-10 (UP) - J9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation)
    Below 1 V
    J9-10 (UP) - J9-1 (GND)
    L - W-B
    Power window motor up input
    Engine switch on (IG), front passenger door power window fully closed
    11 to 14 V


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B316097E25

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).

  2. Reconnect the instrument panel junction block assembly connectors.

  3. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    MB-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    I12-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Engine switch off
    Below 1 V
    MB-31 (ALTB) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    Engine switch power supply
    Engine switch on (IG)
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    Engine switch power supply
    Engine switch off
    Below 1 V

  4. Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly (Click here).

  5. Measure the voltage according to the value(s) in the table below.

  6. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3C-15 (FLCY) - Body ground
    L - Body ground
    Front door courtesy switch LH input
    Front door LH open
    Below 1 V
    3C-15 (FLCY) - Body ground
    L - Body ground
    Front door courtesy switch LH input
    Front door LH closed
    11 to 14 V
    I13-19 (FRCY) - Body ground
    SB - Body ground
    Front door courtesy switch RH input
    Front door RH open
    Below 1 V
    I13-19 (FRCY) - Body ground
    SB - Body ground
    Front door courtesy switch RH input
    Front door RH closed
    11 to 14 V