AUTOMATIC TRANSAXLE FLUID > ADJUSTMENT |
| 1. PRECAUTIONS AND WORK DESCRIPTION |
The U660E automatic transaxle does not have an oil filler tube and oil level gauge. When adding fluid, add fluid through the refill hole on the transaxle case. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the oil pan.
Before adjusting the fluid level, add the specified amount of fluid when the engine is cold and warm up the engine to circulate the fluid in the transaxle. Ensure that the fluid temperature is as specified and the engine is idling.

The U660E automatic transaxle requires Toyota Genuine ATF WS.
The adjustment should be performed according to the procedures and notes.
| 2. WORK FLOW |
The adjustment should be performed according to the procedure referenced in the work flow below.

| 3. PREPARATION WORK |
Lift the vehicle.
Remove the 2 bolts, clip and front fender apron seal LH.
| 4. PERFORM INITIAL FILLING |
![]() |
Remove the refill plug and gasket from the automatic transaxle assembly.
| Operations that do not require initial filling |
|
![]() |
Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle assembly.
![]() |
Using a 6 mm hexagon socket wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Hexagon Socket Wrench |
| *a | Overflow Plug Hole |
Perform initial filling.
![]() |
Fill the transaxle through the refill hole until fluid begins to trickle out of the overflow plug hole.
![]() |
Wait until the fluid flow slows and only drips come out.
![]() |
Temporarily install the overflow plug.
| 5. ADD SPECIFIED AMOUNT OF FLUID |
Fill the transaxle with the correct amount of fluid as listed in the table below.
| Performed Repair | Fill Amount |
| 0.5 liters (0.5 US qts, 0.4 lmp. qts) |
| 2.8 liters (3.0 US qts, 2.5 lmp. qts) |
| Removal and installation of the valve body | 3.2 liters (3.4 US qts, 2.8 lmp. qts) |
| Removal and installation of the transaxle (not including removal of the torque converter) | 3.4 liters (3.6 US qts, 3.0 lmp. qts) |
| Removal and installation of the torque converter (torque converter reused) | 4.8 liters (5.1 US qts, 4.2 lmp. qts) |
| Installation of a new torque converter | 5.3 liters (5.6 US qts, 4.7 lmp. qts) |
![]() |
Temporarily install the refill plug to avoid fluid spillage.
Lower the vehicle.
| 6. ADJUST FLUID TEMPERATURE |
When using the intelligent tester:
Connect the intelligent tester to the DLC3 with the engine switch off.
Turn the engine switch on (IG) and turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test / Connect the TC and TE1.
Select the Active Test item: Connect the TC and TE1 / ON.
Select the Data List menu: A/T Oil Temperature 1.
Check the ATF temperature.
Depress and hold the brake pedal.
Start the engine.
Slowly move the shift lever from P to D, and then back to P.
![]() |
While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.
Check that the D shift indicator comes on for 2 seconds.
Move the shift lever from N to P.
Release the brake pedal.
Select the Active Test item: Connect the TC and TE1 / OFF.
![]() |
Warm up the engine with the engine idling until the fluid temperature reaches the fluid level adjustment temperature (40 to 45°C [104 to 113°F]).
| Below Fluid Level Adjustment Temperature | Fluid Level Adjustment Temperature | Above Fluid Level Adjustment Temperature |
| 40°C or less (104°F or less) | 40 to 45°C (104 to 113°F) | 45°C or more (113°F or more) |
| *a | Turned Off |
| *b | Turned On |
| *c | Blinking |
| Below Fluid Level Adjustment Temperature (40°C or less) (104°F or less) | Fluid Level Adjustment Temperature (40 to 45°C) (104 to 113°F) | Above Fluid Level Adjustment Temperature (45°C or more) (113°F or more) |
| OFF | ON | Blinks |
When not using the intelligent tester:
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the engine switch off.
| *a | DLC3 |
Depress and hold the brake pedal.
Start the engine.
Slowly move the shift lever from P to D, and then back to P.
![]() |
While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.
Check that the D shift indicator comes on for 2 seconds.
Move the shift lever from N to P.
Release the brake pedal.
![]() |
Remove SST from terminals 13 (TC) and 4 (CG).
| *a | DLC3 |
![]() |
Allow the engine to idle until the D shift indicator comes on again.
| *a | Turned Off |
| *b | Turned On |
| *c | Blinking |
| Below Fluid Level Adjustment Temperature (40°C or less) (104°F or less) | Fluid Level Adjustment Temperature (40 to 45°C) (104 to 113°F) | Above Fluid Level Adjustment Temperature (45°C or more) (113°F or more) |
| OFF | ON | Blinks |
| 7. ADJUST FLUID LEVEL |
Lift the vehicle.
Adjust the fluid level.
![]() |
Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket.
Check the amount of fluid that comes out of the overflow plug hole.
![]() |
If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drips come out.
![]() |
If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add transaxle fluid through the refill hole until fluid comes out of the overflow plug hole. Wait until the fluid flow slows and only drips come out.
![]() |
Check that the fluid flow has slowed and only drips come out.
![]() |
Install the overflow plug with a new gasket.
![]() |
Install the refill plug with a new gasket.
Lower the vehicle.
Turn the engine switch off.
Remove the intelligent tester from the DLC3 (when using the intelligent tester).
| 8. REBUILD WORK |
Lift the vehicle.
Clean each part.
Check for fluid leaks.
Install the front wheel opening extension pad LH, engine under covers LH and front fender apron seal LH.
Lower the vehicle.