Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM

REAR VIEW MONITOR SYSTEM > TERMINALS OF ECU

for Preparation Click here



REAR TELEVISION CAMERA ASSEMBLY


  1. Disconnect the T6 rear television camera assembly connector.


    E220918E15

  2. Measure the voltage on the wire harness side connector according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T6-6 (CB+) - Body ground
    L*1, B*2 - Body ground
    Power source
    Ignition switch ACC
    5.5 to 7.05 V

    1. *1: for TMC, TMMR Made
    2. *2: for TMMK Made
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T6 rear television camera assembly connector.

  4. Measure the voltage and check for pulses at each terminal of the connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T6-3 (CV+) - T6-2 (CV-)
    W - R
    Video signal
    Ignition switch ON
    Shift lever in R
    Camera lens not covered, displaying an image
    Pulse generation
    (Refer to waveform 1)
    Ignition switch ON
    Shift lever in R
    Camera lens covered, blacking out screen
    Pulse generation
    (Refer to waveform 2)
    T6-5 (CGND) - Body ground
    LG*1, BR*2 - Body ground
    Shield ground
    Always
    Below 1 V

    1. *1: for TMC, TMMR Made
    2. *2: for TMMK Made

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.

    1. *1: for Navigation System (for Navigation Receiver Type)
    2. *2: for Audio and Visual System (for Radio and Display Type)
    If the result is not as specified, the rear television camera assembly may be malfunctioning.



  5. E171712E22
  6. Reference (Oscilloscope waveform):

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.

    1. *1: for Navigation System (for Navigation Receiver Type)
    2. *2: for Audio and Visual System (for Radio and Display Type)

    1. Waveform 1 (camera lens is not covered, displaying an image)
      Item
      Content
      Measurement terminal
      T6-3 (CV+) - T6-2 (CV-)
      Measurement setting
      200 mV/DIV., 50 μs./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      1. The video waveform changes according to the image sent by the rear television camera assembly.
      2. The video waveform is constantly output when the ignition switch is turned to ACC.

    2. Waveform 2 (camera lens is covered, blacking out the screen)
      Item
      Content
      Measurement terminal
      T6-3 (CV+) - T6-2 (CV-)
      Measurement setting
      200 mV/DIV., 50 μs./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      1. The video waveform changes according to the image sent by the rear television camera assembly.
      2. The video waveform is constantly output when the ignition switch is turned to ACC.

      Text in Illustration 
      *a
      Waveform 1 (camera lens is not covered, displaying an image)
      *b
      Waveform 2 (camera lens is covered, blacking out the screen)
      *c
      Synchronization Signal
      *d
      Video Waveform


NAVIGATION RECEIVER ASSEMBLY (for Navigation System (for Navigation Receiver Type)) (Click here)

RADIO AND DISPLAY RECEIVER ASSEMBLY (for Audio and Visual System (for Radio and Display Type)) (Click here)