Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)

SEAT BELT WARNING SYSTEM (w/ Occupant Classification System) > TERMINALS OF ECU

for Preparation Click here



CHECK COMBINATION METER ASSEMBLY


  1. Disconnect the I18 combination meter assembly connector.


    E224288E06

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I18-20 (ES) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the I18 combination meter assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I18-1 (B) - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    I18-13 (IG+) - Body ground
    L - Body ground
    Ignition power supply
    (IG signal)
    Ignition switch off
    Below 1 V
    I18-13 (IG+) - Body ground
    L - Body ground
    Ignition power supply
    (IG signal)
    Ignition switch ON
    11 to 14 V
    If the result is not as specified, the combination meter assembly may have a malfunction.


CHECK AIRBAG SENSOR ASSEMBLY

C109532E49


Terminal No.
Terminal Symbol
Destination
N5-10
LBE+
Front seat inner belt assembly LH
N5-18
LBE-
Front seat inner belt assembly LH
O7-16
FSR+
Occupant detection ECU
O7-24
FSR-
Occupant detection ECU

CHECK OCCUPANT DETECTION ECU


  1. Measure the voltage according to the value(s) in the table below.


    C238368E20


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    d11-1 (+B) - d11-3 (GND)
    W - W-B
    Battery
    Always
    11 to 14 V
    d11-2 (DIA) - d11-3 (GND)
    GR - W-B
    Diagnosis (DLC3)
    Ignition switch ON, GTS not connected to DLC3
    Below 1 V
    d11-3 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    d11-4 (FSR-) - d11-3 (GND)
    Y - W-B
    Airbag sensor assembly communication line
    Always
    Below 1 V
    d11-5 (BGND) - d11-3 (GND)
    P - W-B
    Front passenger buckle switch ground line
    Always
    Below 1 V
    d11-6 (IG2) - d11-3 (GND)
    B - W-B
    Power source
    Ignition switch ON
    11 to 14 V
    d11-7 (FSR+) - d11-4 (FSR-)
    L - Y
    Airbag sensor assembly communication line
    Ignition switch ON
    Pulse generation
    d11-8 (BSW) - d11-5 (BGND)
    G - P
    Front passenger buckle switch line
    Always
    Pulse generation
    d8-1 (SVC1) - d8-5 (SGD1)
    R - G
    Front occupant classification sensor power supply line
    Ignition switch ON
    4.9 to 5.1 V
    d8-2 (SVC3) - d8-6 (SGD3)
    GR - W
    Rear occupant classification sensor power supply line
    Ignition switch ON
    4.9 to 5.1 V
    d8-3 (SIG1) - d8-5 (SGD1)
    P - G
    Front occupant classification sensor signal line
    Ignition switch ON
    Pulse generation
    d8-4 (SIG3) - d8-6 (SGD3)
    Y - W
    Rear occupant classification sensor signal line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, the occupant detection ECU may have a malfunction.