Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR (for TMMK Made)

OUTER REAR VIEW MIRROR (for TMMK Made) > INSPECTION

for Preparation Click here



1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


  1. Check the operation of the mirror surface.



      B281818E01
    1. Disconnect the outer rear view mirror assembly RH connector.

    2. Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (MV)
      Battery negative (-) → Terminal 5 (M+)
      Turns upward
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 6 (MV)
      Turns downward
      Battery positive (+) → Terminal 4 (MH)
      Battery negative (-) → Terminal 5 (M+)
      Turns left
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 4 (MH)
      Turns right

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



  1. Check the operation of the retractable mirror.

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.




      B199932E13
    1. Disconnect the outer rear view mirror assembly RH connector.

    2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK:
      Tester Connection
      Condition
      Specified Condition
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      Text in Illustration 
      *1
      (A) Forward Position
      *2
      (B)
      *3
      (C) Driving position
      *4
      (D)
      *5
      (E) Retracted Position
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


  1. Check the operation of the mirror surface.



      B281822E01
    1. Disconnect the outer rear view mirror assembly LH connector.

    2. Apply battery voltage and check the operation of the mirror.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (MV)
      Battery negative (-) → Terminal 5 (M+)
      Turns upward
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 6 (MV)
      Turns downward
      Battery positive (+) → Terminal 4 (MH)
      Battery negative (-) → Terminal 5 (M+)
      Turns left
      Battery positive (+) → Terminal 5 (M+)
      Battery negative (-) → Terminal 4 (MH)
      Turns right

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



  1. Check the operation of the retractable mirror.

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.




      B199933E12
    1. Disconnect the outer rear view mirror assembly LH connector.

    2. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK:
      Tester Connection
      Condition
      Specified Condition
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 3 (MR)
      Battery negative (-) → Terminal 9 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 9 (MF)
      Battery negative (-) → Terminal 3 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      Text in Illustration 
      *1
      (A) Forward Position
      *2
      (B)
      *3
      (C) Driving position
      *4
      (D)
      *5
      (E) Retracted Position
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.