Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH

OUTER MIRROR SWITCH > INSPECTION

for Preparation Click here



1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)


  1. Check the mirror select switch and mirror surface adjust switch. (except TMMK Made)



      B254629E11
    1. Turn the mirror select switch to the L position.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for left side):
      Tester Connection
      Condition
      Specified Condition
      4 (MLV) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      4 (MLV) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      5 (MLH) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      5 (MLH) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher

    3. Turn the mirror select switch to the R position.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for right side):
      Tester Connection
      Condition
      Specified Condition
      3 (MRV) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      3 (MRV) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      2 (MRH) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      2 (MRH) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher

      Text in Illustration 
      *1
      Mirror select switch
      *2
      Mirror surface adjust switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)
      If the result is not as specified, replace the outer mirror switch assembly.



  1. Check the mirror retract switch. (except TMMK Made)



      B254629E05
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      10 (MF) - 7 (E)
      Mirror retract switch retract position
      Below 1 Ω
      9 (MR) - 8 (B)
      Below 1 Ω
      10 (MF) - 8 (B)
      Mirror retract switch return position
      Below 1 Ω
      9 (MR) - 7 (E)
      Below 1 Ω

      Text in Illustration 
      *1
      Mirror retract switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)
      If the result is not as specified, replace the outer mirror switch assembly.



  1. Check the mirror select switch and mirror surface adjust switch. (for TMMK Made)



      B336515E01
    1. Turn the mirror select switch to the L position.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for left side):
      Tester Connection
      Switch Condition
      Specified Condition
      15 (VL) - 19 (B)
      17 (M+) - 18 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      15 (VL) - 18 (E)
      17 (M+) - 19 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      16 (HL) - 19 (B)
      17 (M+) - 18 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      16 (HL) - 18 (E)
      17 (M+) - 19 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher

    3. Turn the mirror select switch to the R position.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for right side):
      Tester Connection
      Switch Condition
      Specified Condition
      14 (VR) - 19 (B)
      17 (M+) - 18 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      14 (VR) - 18 (E)
      17 (M+) - 19 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      13 (HR) - 19 (B)
      17 (M+) - 18 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      13 (HR) - 18 (E)
      17 (M+) - 19 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher
      Text in Illustration 
      *1
      Mirror select switch
      *2
      Mirror surface adjust switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

      If the result is not as specified, replace the outer mirror switch assembly.



  1. Check the mirror retract switch. (for TMMK Made)



      B336515E02
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      21 (MF) - 18 (E)
      Mirror retract switch retract position
      Below 1 Ω
      20 (MR) - 19 (B)
      Below 1 Ω
      21 (MF) - 19 (B)
      Mirror retract switch return position
      Below 1 Ω
      20 (MR) - 18 (E)
      Below 1 Ω
      Text in Illustration 
      *1
      Mirror retract switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

      If the result is not as specified, replace the outer mirror switch assembly.



2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)


    B295604E11
  1. Check the switch functions.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (M+) - 2 (E1)
      Mirror adjust switch pressed up
      90 to 110 Ω
      Mirror adjust switch pressed down
      437 to 503 Ω
      Mirror adjust switch pressed left
      744 to 856 Ω
      Mirror adjust switch pressed right
      225 to 275 Ω
      Mirror adjust switch not pressed
      10 kΩ or higher
      1 (MSW) - 2 (E1)
      Mirror select switch R
      Below 1 Ω
      Mirror select switch L
      90 to 110 Ω
      Mirror select switch off
      10 kΩ or higher

      Text in Illustration 
      *1
      Mirror Adjust Switch
      *2
      Mirror Select Switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)
      If the result is not as specified, replace the outer mirror switch assembly.



  1. Check the mirror retract switch.



      B295604E12
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      8 (MF) - 4 (E2)
      Mirror retract switch retract position
      Below 1 Ω
      7 (MR) - 6 (B)
      Below 1 Ω
      8 (MF) - 6 (B)
      Mirror retract switch return position
      Below 1 Ω
      7 (MR) - 4 (E2)
      Below 1 Ω
      7 (MR) - 8 (MF)
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Mirror retract switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)
      If the result is not as specified, replace the outer mirror switch assembly.