Home › Drivetrain · U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0796    Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3)

for Preparation Click here


SYSTEM DESCRIPTION

The ECM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves and valve body.

DTC No.
DTC Detection Condition
Trouble Area
P0796
The engine revs freely when 2nd or 6th gear is commanded (2-trip detection logic).
When the following is detected twice (2-trip detection logic):
  1. When 1st gear is commanded, 2nd gear is engaged.
  1. Shift solenoid valve SL3 remains open or closed.
  2. Valve body is blocked.
  3. Automatic transaxle (clutch, brake or gear etc.)

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft revolution (speed), intermediate (counter) shaft revolution (speed) and output shaft revolution (speed), the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores the DTC.

INSPECTION PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0796)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs using the intelligent tester.

    Result:

    Display (DTC Output)
    Proceed to
    Only "P0796" is output
    A
    "P0796" and other DTCs are output
    B

HINT:
If a solenoid is stuck off, DTCs for several solenoids including the malfunctioning solenoid will be detected.



A
Go to step 3
B


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NOTICE:
This test should always be performed with at least 2 people.

  1. Warm up the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    HINT:
    Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem (Click here).

    Tester Display
    Test Details
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operates the shift solenoid valves to allow gears to selected manually.
    1. Press "→" button: Upshift occurs
    2. Press "←" button: Downshift occurs
    Can be used to check the operation of the shift solenoid valves.
    Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
    Do not downshift at high speeds.
    Doing so will damage the automatic transaxle.
    [Vehicle Condition]
    50 km/h (30 mph) or less

    NOTICE:
    1. This test can be conducted when the vehicle is stopped.
    2. When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.

    HINT:
    The gear commanded by the ECM is shown in the Data List / Shift Status display on the intelligent tester.

  1. Check the vehicle speed and the gear when the engine speed is 1000 rpm.

    HINT:
    Because the torque converter has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gear, however a difference of speed should still be evident following each gear change.


    Standard:

    1st
    2nd
    3rd
    4th
    5th
    6th
    8 to 12 km/h (5 to 7.5 mph)
    15 to 19 km/h (9.3 to 11.8 mph)
    21 to 25 km/h (13.0 to 15.5 mph)
    31 to 35 km/h (19.3 to 21.7 mph)
    44 to 48 km/h (27.3 to 29.8 mph)
    52 to 56 km/h (32.3 to 34.8 mph)

  1. Compare the ECM commanded gear and the actual gear.

    Result:

    Actuator Gear during Malfunction
    ECM Commanded Gear
    Proceed to
    1st
    2nd
    3rd
    4th
    5th
    6th
    Shift solenoid SL1
    Stuck ON
    1st
    2nd
    3rd
    4th
    4th
    4th
    A
    Stuck OFF
    N*1
    N*1
    N*1
    N*1
    5th
    6th
    Shift solenoid SL2
    Stuck ON
    4th
    4th
    4th
    4th
    5th
    6th
    B
    Stuck OFF
    1st
    2nd
    3rd
    1st
    N*1
    N*1
    Shift solenoid SL3
    Stuck ON
    2nd
    2nd
    3rd
    4th
    5th
    6th
    C
    Stuck OFF
    1st
    1st
    3rd
    4th
    5th
    N*1
    Shift solenoid SL4
    Stuck ON*3
    3rd
    3rd
    3rd
    4th
    5th
    5th
    D
    Stuck OFF
    1st
    2nd
    1st
    4th
    N*1
    6th
    Shift solenoid SLT
    Stuck ON
    N*2
    N*2
    N*2
    N*2
    N*2
    N*2
    E
    Stuck OFF*3
    1st
    2nd
    3rd
    4th
    5th
    6th

    HINT:
    1. *1: Neutral
    2. *2: If shift solenoid SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
    3. *3: When shift solenoid SLT is stuck off, gear shifting is normal.



A
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL1) PERFORMANCE DTC P0746) (Click here)

B
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL2) PERFORMANCE DTC P0776) (Click here)

D
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SL4) PERFORMANCE DTC P2808) (Click here)

E
GO TO DTC CHART (RELATED SHIFT SOLENOID VALVE (SLT) PERFORMANCE DTC P2714) (Click here)
C


3.INSPECT SHIFT SOLENOID VALVE SL3


    C201747E01
  1. Remove shift solenoid valve SL3.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes an operating sound.

    Text in Illustration 
    *1
    Shift Solenoid Valve SL3



NG
REPLACE SHIFT SOLENOID VALVE SL3 (Click here)
OK


4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on each valve and they operate smoothly.



NG
REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPLACE AUTOMATIC TRANSAXLE ASSEMBLY (Click here)