Home › Drivetrain ยท U760E AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY

VALVE BODY ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL MANUAL VALVE
  1. Coat the manual valve with ATF and install it to the transmission valve body assembly.



2. INSTALL TRANSAXLE CASE GASKET
  1. Coat 2 new transaxle case gaskets with ATF.

  1. Install the 2 transaxle case gaskets to the automatic transaxle assembly.



3. INSTALL TRANSMISSION VALVE BODY ASSEMBLY
  1. Coat the O-ring of the transmission wire with ATF.



    C325107E01
  1. Insert the manual valve lever shaft sub-assembly pin into the groove on the end of the manual valve as shown in the illustration and temporarily install the transmission valve body assembly to the transaxle case sub-assembly with the 11 bolts.
    Text in Illustration 
    *1
    Manual Valve Lever Shaft Sub-assembly
    *2
    Manual Valve
    *a
    Positioning Bolt

    NOTICE:
    1. When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.
    2. Be sure to insert the manual valve lever shaft sub-assembly pin into the groove on the end of the manual valve.

    Bolt Length 
    Bolt
    Length [mm (in.)]
    (A)
    25 (0.984)
    (B)
    30 (1.18)
    (C) and (D)
    35 (1.38)

  1. Fully tighten the 2 positioning bolts shown in the illustration.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Fully tighten the 9 bolts to install the transmission valve body assembly.

    Torque:
    Bolt (A), (B), (C):
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    Bolt (D):
    9.6 N*m{ 98 kgf*cm , 85 in.*lbf }



4. INSTALL VALVE BODY OIL STRAINER ASSEMBLY
  1. Coat a new O-ring with ATF.



    C201703E02
  1. Install the O-ring to the valve body oil strainer assembly.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Ensure that the O-ring is not twisted.



    C201702
  1. Install the valve body oil strainer assembly to the transmission valve body assembly with the 2 bolts.

    Torque:
    9.6 N*m{ 98 kgf*cm , 85 in.*lbf }



5. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C306066E01
  1. Install the 4 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Transmission Oil Cleaner Magnet

  1. Install a new automatic transaxle oil pan gasket to the automatic transaxle oil pan sub-assembly.



    C298184
  1. Clean and degrease the 2 bolts and the installation holes in the automatic transaxle assembly.



    C202902
  1. Install the automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket to the automatic transaxle assembly with the 17 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    Completely remove any oil or grease from the contact surfaces of the automatic transaxle assembly and automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket before installation.

  1. Apply adhesive to 2 or 3 threads on the ends of the 2 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    In order to ensure proper sealing of the 2 bolts, apply adhesive to the 2 bolts and install them within 10 minutes of adhesive application.



    C202903
  1. Install the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



6. INSTALL TORQUE CONVERTER ASSEMBLY


    C201725
  1. Engage the splines of the input shaft and turbine runner.



    C201726
  1. Engage the splines of the stator shaft and the stator while turning the torque converter assembly.

    HINT:
    If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm and engage the splines while rotating the torque converter.



    C201727
  1. Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.

  1. Clean the torque converter set bolt holes.



    C201728E02
  1. Using a vernier caliper and straightedge, measure dimension A between the transaxle contact surface of the engine and the torque converter contact surface of the drive plate.
    Text in Illustration 
    *a
    Engine Surface
    *b
    Drive Plate Surface

    NOTICE:
    Make sure to deduct the thickness of the straightedge.



    C207515E01
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.

    Standard:
    A + 1 mm (0.0394 in.) or more

    NOTICE:
    1. Make sure to deduct the thickness of the straightedge.
    2. If the automatic transaxle assembly is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.



7. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

HINT:
See the steps from "Install Automatic Transaxle Assembly" through "Check Automatic Transaxle System" (Click here).



8. CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:
If automatic transmission parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary (Click here).