Home › Power Source / Network ยท 2AR-FE BATTERY / CHARGING › GENERATOR (for 100 A, 130 A Type)

GENERATOR (for 100 A, 130 A Type) > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR DRIVE END FRAME BEARING


    A192789E01
  1. Using SST and a press, install a new generator drive end frame bearing.

    SST
    09950-60010   (09951-00520)
    09950-70010   (09951-07100)



    A211515E04
  1. Fit the tabs of the retainer plate into the cutouts of the generator drive end frame to install the retainer plate.
    Text in Illustration 
    *a
    Tab
    *b
    Cutout

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }



2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the generator drive end frame on the generator pulley with clutch.

  1. Install the generator rotor assembly to the generator drive end frame.



3. INSTALL GENERATOR COIL ASSEMBLY


    A314531E01
  1. Install a new bearing cover packing.
    Text in Illustration 
    *a
    Protrusion
    *b
    Groove

    NOTICE:
    Align the protrusions of the bearing cover packing with the grooves of the generator coil assembly when installing.



    A192792E05
  1. Using a 21 mm deep socket wrench and press, slowly press the generator coil assembly to install it.
    Text in Illustration 
    *a
    Deep Socket Wrench (21 mm)

  1. Install the 4 bolts.

    Torque:
    5.6 N*m{ 57 kgf*cm , 50 in.*lbf }



4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


    A079315E30
  1. While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.
    Text in Illustration 
    *a
    Pin (1.0 mm)



    A192793E07
  1. Install the generator brush holder assembly to the generator coil assembly with the 2 screws.
    Text in Illustration 
    *a
    Pin

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Pull out the pin from the generator brush holder assembly hole.



5. INSTALL GENERATOR REAR END COVER
  1. Install the generator terminal insulator to the generator coil assembly.

    NOTICE:
    Be sure to install the generator terminal insulator in the correct direction.

  1. Install the generator rear end cover to the generator coil assembly with the 3 bolts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }



6. INSTALL GENERATOR PULLEY WITH CLUTCH
  1. Secure the generator assembly in a vise between aluminum plates.

  1. Temporarily install the generator pulley with clutch to the rotor shaft.



    A197238E04
  1. Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.
    Text in Illustration 
    *a
    Rotor Shaft

    SST
    09820-63021  



    A333106E01
  1. Tighten the generator pulley with clutch by turning SST (B) as shown in the illustration.
    Text in Illustration 
    *a
    Torque Wrench Fulcrum Length

    Torque:
    Specified tightening torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Check that the generator assembly is secured in the vise tightly.
    2. Hold SST (A) tightly during the operation.

    HINT:
    1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
    2. When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 57 N*m (581 kgf*cm, 42 ft.*lbf)

  1. Remove SST (A) and (B) from the generator pulley with clutch.

  1. Check that the generator pulley with clutch rotates smoothly.

  1. Remove the generator assembly from the vise.



7. INSTALL GENERATOR PULLEY CAP
  1. Install a new generator pulley cap to the generator pulley with clutch.