Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

DTC    B15DA    Rear Console Recognition Disconnected

for Preparation Click here


DESCRIPTION

The navigation receiver assembly and cooler control switch assembly are connected via AVC-LAN communication lines.
This DTC is stored when an AVC-LAN communication error occurs between the navigation receiver assembly and cooler control switch assembly.

DTC No.
DTC Detection Condition
Trouble Area
B15DA
When either of the following conditions is met:
  1. Cooler control switch assembly is not connected while the ignition switch is ON or ACC.
  2. Communication between the master unit and the cooler control switch assembly is not possible when the engine is started.
  1. Cooler control switch assembly power source circuit
  2. AVC-LAN circuit between navigation receiver assembly and cooler control switch assembly
  3. Cooler control switch assembly
  4. Navigation receiver assembly
  5. Harness or connector

HINT:
The navigation receiver assembly is the master unit.


WIRING DIAGRAM


E299415E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result:
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

HINT:
  1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
  2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 3
A


2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END 

4.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY POWER SOURCE)
  1. Disconnect the X1 cooler control switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X1-16 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    X1-1 (+B) - X1-16 (GND)
    Always
    11 to 14 V
    X1-7 (IG+) - X1-16 (GND)
    Ignition switch ON
    11 to 14 V
    X1-6 (ACC) - X1-16 (GND)
    Ignition switch ACC
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COOLER CONTROL SWITCH ASSEMBLY)
  1. Disconnect the I67 navigation receiver assembly connector.

  1. Disconnect the X1 cooler control switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-7 (TX1+) - X1-15 (TX+)
    Always
    Below 1 Ω
    I67-8 (TX1-) - X1-5 (TX-)
    Always
    Below 1 Ω
    I67-7 (TX1+) - Body ground
    Always
    10 kΩ or higher
    I67-8 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE COOLER CONTROL SWITCH ASSEMBLY
  1. Replace the cooler control switch assembly with a new or known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC Made)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A

END