Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

NAVIGATION SYSTEM (for Navigation Receiver Type) > AVC-LAN Circuit

for Preparation Click here


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transmits switch signals via AVC-LAN communication.
If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM


w/ Cooler Control Switch Assembly

E277861E15


for TMMK Made

E277861E25


INSPECTION PROCEDURE

HINT:
The navigation receiver assembly is the master unit.

1.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Remove the navigation receiver assembly (for TMMK Made) (Click here).
    Remove the navigation receiver assembly (for TMC Made) (Click here).



    E221758E26
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    7 (TX1+) - 8 (TX1-)
    Always
    60 to 80 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Navigation Receiver Assembly)

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC Made)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A


2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
  1. Disconnect the I67 navigation receiver assembly connector.

  1. Disconnect the X1 cooler control switch assembly connector (w/ Cooler Control Switch Assembly).

  1. Disconnect the I69 stereo component amplifier assembly connector (for TMMK Made).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (w/ Cooler Control Switch Assembly):
    Tester Connection
    Condition
    Specified Condition
    X1-15 (TX+) - I67-7 (TX1+)
    Always
    Below 1 Ω
    X1-5 (TX-) - I67-8 (TX1-)
    Always
    Below 1 Ω
    X1-15 (TX+) - Body ground
    Always
    10 kΩ or higher
    X1-5 (TX-) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for TMMK Made):
    Tester Connection
    Condition
    Specified Condition
    I69-8 (TX+) - I67-7 (TX1+)
    Always
    Below 1 Ω
    I69-7 (TX-) - I67-8 (TX1-)
    Always
    Below 1 Ω
    I69-8 (TX+) - Body ground
    Always
    10 kΩ or higher
    I69-7 (TX-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT MALFUNCTIONING PARTS
  1. Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

    HINT:
    1. Check all slave units.
    2. If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.

    OK:
    Master unit returns to normal.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC Made)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A

REPLACE MALFUNCTIONING PARTS