CYLINDER BLOCK > INSPECTION |
| 1. INSPECT CYLINDER BLOCK FOR WARPAGE |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the cylinder head gasket contact surface.
| 2. INSPECT CYLINDER BORE |
![]() |
Using a cylinder gauge, measure the cylinder bore diameter at positions (A) and (B) in the thrust and axial directions.
| *a | Axial Direction |
| *b | Thrust Direction |
| *c | Center |
![]() | Front |
| 3. INSPECT PISTON |
![]() |
Using a gasket scraper, remove the carbon from the piston top.
![]() |
Using a groove cleaning tool or a broken ring, clean the piston ring grooves.
![]() |
Using a brush and solvent, thoroughly clean the piston.
![]() |
Using a micrometer, measure the piston diameter at a right angle to the piston center line, and at a position that is 10.5 mm (0.413 in.) from the bottom of the piston.
| 4. INSPECT PISTON OIL CLEARANCE |
Measure the cylinder bore diameter in the thrust direction.
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
| 5. INSPECT RING GROOVE CLEARANCE |

| *A | Type A | *B | Type B |
| *1 | Piston | *2 | Oil Ring |
![]() |
Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
| Item | Specified Condition |
| No. 1 ring | 0.020 to 0.070 mm (0.000787 to 0.00276 in.) |
| No. 2 ring | 0.020 to 0.060 mm (0.000787 to 0.00236 in.) |
| Oil ring | 0.020 to 0.070 mm (0.000787 to 0.00276 in.) |
| Item | Specified Condition |
| No. 1 ring | 0.020 to 0.070 mm (0.000787 to 0.00276 in.) |
| No. 2 ring | 0.020 to 0.060 mm (0.000787 to 0.00236 in.) |
| Oil ring | 0.060 to 0.120 mm (0.00236 to 0.00472 in.) |
| 6. INSPECT PISTON RING END GAP |

| *A | Type A | *B | Type B |
| *1 | Piston | *2 | Oil Ring |
![]() |
Insert the piston ring into the cylinder bore.
| *a | Piston Ring |
Using a piston, push in the piston ring a little beyond the bottom of the ring travel, 120 mm (4.72 in.) from the top of the cylinder block sub-assembly.
![]() |
Using a feeler gauge, measure the end gap.
| Item | Specified Condition |
| No. 1 compression ring | 0.22 to 0.27 mm (0.00866 to 0.0106 in.) |
| No. 2 compression ring | 0.37 to 0.42 mm (0.0146 to 0.0165 in.) |
| Oil ring | 0.10 to 0.20 mm (0.00394 to 0.00787 in.) |
| Item | Specified Condition |
| No. 1 compression ring | 0.22 to 0.27 mm (0.00866 to 0.0106 in.) |
| No. 2 compression ring | 0.50 to 0.55 mm (0.0197 to 0.0217 in.) |
| Oil ring | 0.10 to 0.35 mm (0.00394 to 0.0138 in.) |
| Item | Specified Condition |
| No. 1 compression ring | 0.87 mm (0.0343 in.) |
| No. 2 compression ring | 1.02 mm (0.0402 in.) |
| Oil ring | 0.80 mm (0.0315 in.) |
| Item | Specified Condition |
| No. 1 compression ring | 0.87 mm (0.0343 in.) |
| No. 2 compression ring | 1.15 mm (0.0453 in.) |
| Oil ring | 0.95 mm (0.0374 in.) |
| 7. INSPECT PISTON PIN OIL CLEARANCE |
Check each mark on the piston, piston pin and connecting rod sub-assembly.

| *a | Front Mark | *b | Piston Pin Hole Inside Diameter Mark |
| *c | Connecting Rod Small End Bush Inside Diameter Mark | - | - |
![]() |
Using a caliper gauge, measure the inside diameter of the piston pin hole.
| Item | Specified Condition |
| Mark A | 22.001 to 22.004 mm (0.86618 to 0.86630 in.) |
| Mark B | 22.005 to 22.007 mm (0.86634 to 0.86642 in.) |
| Mark C | 22.008 to 22.010 mm (0.86645 to 0.86653 in.) |
![]() |
Using a micrometer, measure the piston pin diameter.
| Item | Specified Condition |
| Mark A | 21.997 to 22.000 mm (0.86602 to 0.86614 in.) |
| Mark B | 22.001 to 22.003 mm (0.86618 to 0.86626 in.) |
| Mark C | 22.004 to 22.006 mm (0.86630 to 0.86638 in.) |
![]() |
Using a caliper gauge, measure the connecting rod small end bush inside diameter.
| Item | Specified Condition |
| Mark A | 22.005 to 22.008 mm (0.86634 to 0.86645 in.) |
| Mark B | 22.009 to 22.011 mm (0.86649 to 0.86657 in.) |
| Mark C | 22.012 to 22.014 mm (0.86661 to 0.86669 in.) |
Subtract the piston pin diameter measurement from the piston pin hole inside diameter measurement.
Subtract the piston pin diameter measurement from the connecting rod small end bush inside diameter measurement.
| 8. INSPECT CONNECTING ROD SUB-ASSEMBLY |
![]() |
Using a connecting rod aligner and feeler gauge, check the connecting rod alignment.
Check for bend.
![]() |
Check for twist.
| 9. INSPECT CRANKSHAFT |
![]() |
Inspect for runout.
Using a dial indicator and V-blocks, measure the runout as shown in the illustration.
![]() |
Inspect the main journals.
Using a micrometer, measure the diameter of each main journal.
Check each main journal for taper and out-of-round as shown in the illustration.
![]() |
Inspect the crank pin.
Using a micrometer, measure the diameter of each crank pin.
Inspect each crank pin for taper and out-of-round as shown in the illustration.
| 10. INSPECT CRANKSHAFT OIL CLEARANCE |
Install the crankshaft bearings .
Install the crankshaft thrust washers .
Clean each main journal and crankshaft bearing.
Place the crankshaft onto the cylinder block sub-assembly.
![]() |
Lay a strip of Plastigage across each journal.
| *a | Plastigage |
Install the crankshaft bearing caps .
Remove the crankshaft bearing caps .
![]() |
Measure the Plastigage at its widest point.
| *a | Plastigage |

| *a | Cylinder Block Number Mark (A) | *b | Crankshaft Number Mark (B) |
| *c | Diameter Mark | - | - |
| (A) + (B) | Use Crankshaft Bearing |
| 0 to 2 | 1 |
| 3 to 5 | 2 |
| 6 to 8 | 3 |
| 9 to 11 | 4 |
| Item | Specified Condition |
| Mark 0 | 59.000 to 59.002 mm (2.32283 to 2.32291 in.) |
| Mark 1 | 59.003 to 59.004 mm (2.32295 to 2.32299 in.) |
| Mark 2 | 59.005 to 59.006 mm (2.32303 to 2.32307 in.) |
| Mark 3 | 59.007 to 59.009 mm (2.32311 to 2.32318 in.) |
| Mark 4 | 59.010 to 59.011 mm (2.32322 to 2.32326 in.) |
| Mark 5 | 59.012 to 59.013 mm (2.32330 to 2.32334 in.) |
| Mark 6 | 59.014 to 59.016 mm (2.32338 to 2.32346 in.) |
| Item | Specified Condition |
| Mark 0 | 54.999 to 55.000 mm (2.16531 to 2.16535 in.) |
| Mark 1 | 54.997 to 54.998 mm (2.16523 to 2.16527 in.) |
| Mark 2 | 54.995 to 54.996 mm (2.16515 to 2.16519 in.) |
| Mark 3 | 54.993 to 54.994 mm (2.16507 to 2.16511 in.) |
| Mark 4 | 54.991 to 54.992 mm (2.16500 to 2.16504 in.) |
| Mark 5 | 54.988 to 54.990 mm (2.16488 to 2.16496 in.) |
| Item | Specified Condition |
| Mark 1 | 1.991 to 1.994 mm (0.07839 to 0.07850 in.) |
| Mark 2 | 1.995 to 1.997 mm (0.07854 to 0.07862 in.) |
| Mark 3 | 1.998 to 2.000 mm (0.07866 to 0.07874 in.) |
| Mark 4 | 2.001 to 2.003 mm (0.07878 to 0.07886 in.) |
Perform the inspection above for each journal.
| 11. INSPECT CRANKSHAFT BEARING CAP BOLT |
![]() |
Using a vernier caliper, measure the diameter of the threads at the measurement point shown in the illustration.
| *a | Measurement Point |
| 12. INSPECT CONNECTING ROD BOLT |
![]() |
Using a vernier caliper, measure the diameter of the connecting rod bolt in the area shown in the illustration.
| *a | Measurement Area |
| 13. INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Push the check valve with a pin to check if it is stuck.
| *a | Pin |
Push the check valve with a pin to check if it moves smoothly.
If it does not move smoothly, clean or replace the No. 1 oil nozzle sub-assembly.
![]() |
Apply air into (A). Check that air does not leak through (B).
If air leaks, clean or replace the No. 1 oil nozzle sub-assembly.
![]() |
Push the check valve with a pin while applying air into (A). Check that air passes through (B).
| *a | Pin |
| 14. INSPECT NO. 2 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Push the check valve with a pin to check if it is stuck.
| *a | Pin |
Push the check valve with a pin to check if it moves smoothly.
If it does not move smoothly, clean or replace the No. 2 oil nozzle sub-assembly.
![]() |
While covering (A), apply air into (B). Check that air does not leak through (C). Perform the check again while covering (B) and applying air into (A).
If air leaks, clean or replace the No. 2 oil nozzle sub-assembly.
![]() |
Push the check valve with a pin while covering (A), and apply air into (B). Check that air passes through (C). Perform the check again while covering (B), pushing the check valve and applying air into (A).
| *a | Pin |