Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System) > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY ECU ASSEMBLY


  1. Disconnect the I19 transponder key ECU assembly connector.


    B255101E02

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I19-1 (+B) - I19-5 (GND)
    W - BR
    Battery
    Always
    11 to 14 V
    I19-2 (IG) - I19-5 (GND)
    R - BR
    Ignition switch signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    I19-3 (KSW) - I19-5 (GND)
    G - BR
    Unlock warning switch signal
    No door control transmitter assembly in ignition key cylinder
    10 kΩ or higher
    Door control transmitter assembly in ignition key cylinder
    Below 1 Ω
    I19-5 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I19 transponder key ECU assembly connector.

  4. Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I19-8 (IND) - I19-5 (GND)
    L - BR
    Security indicator signal
    No door control transmitter assembly in ignition key cylinder, or 20 sec. elapsed after turning ignition switch to ACC or off (engine immobiliser system set)
    Pulse generation
    Door control transmitter assembly in ignition key cylinder (engine immobiliser system unset)
    Below 1 V
    I19-9 (D) - I19-5 (GND)
    GR - BR
    DLC3 communication
    Without communication
    Below 1 V
    During communication
    Pulse generation
    I19-4 (ANT1) - I19-5 (GND)
    LG - BR
    Transponder key amplifier power source
    No door control transmitter assembly in ignition key cylinder
    4 to 6 V
    Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder
    Pulse generation
    (See waveform 1)
    I19-9 (D) - I19-5 (GND)
    GR - BR
    Transponder key amplifier communication signal
    No door control transmitter assembly in ignition key cylinder
    4 to 6 V
    Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder
    Pulse generation
    (See waveform 2)
    I19-12 (EFII) - I19-5 (GND)
    R - BR
    ECM input signal
    Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
    Pulse generation
    (See waveform 3)
    I19-13 (EFIO) - I19-5 (GND)
    G - BR
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation
    (See waveform 4)
    If the result is not as specified, the transponder key ECU assembly may be malfunctioning.



  5. Using an oscilloscope, check the waveform.



    1. Waveform 1 (Reference)


      B329909E07

      Tester Connection
      I19-4 (ANT1) - I19-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder



    2. Waveform 2 (Reference)


      B329910E07

      Tester Connection
      I19-15 (ANT2) - I19-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder



    3. Waveform 3 (Reference)


      B325134E04


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      I19-12 (EFII) - I19-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal



    4. Waveform 4 (Reference)


      B333259E04


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      I19-13 (EFIO) - I19-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM

A247842E19

HINT:
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage or resistance for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
E26-16 (E1) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
A25-1 (BATT) - E26-16 (E1)
GR - BR
+B power supply
Always
11 to 14 V
A25-3 (+B2) - E26-16 (E1)
LG - BR
+B power supply
Ignition switch ON
11 to 14 V
A25-2 (+B) - E26-16 (E1)
P - BR
+B power supply
Ignition switch ON
11 to 14 V
A25-29 (IMO) - E26-16 (E1)
G - BR
Transponder key ECU assembly communication input
Ignition switch off
11 to 14 V
A25-29 (IMO) - E26-16 (E1)
G - BR
Transponder key ECU assembly communication input
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
Pulse generation
(See waveform 1)
A25-28 (IMI) - E26-16 (E1)
Y - BR
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
A25-28 (IMI) - E26-16 (E1)
Y - BR
Transponder key ECU assembly communication output
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
Pulse generation
(See waveform 2)


  1. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




    1. Waveform 1 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      A25-29 (IMO) - E26-16 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal



    2. Waveform 2 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      A25-28 (IMI) - E26-16 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal