Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

DTC    B2784    Antenna Coil Open / Short

for Preparation Click here


DESCRIPTION

When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC.

DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2784
The antenna coil in the transponder key coil is open/shorted.
  1. Wire harness or connector
  2. Transponder key coil
  3. Transponder key ECU assembly
Insert the door control transmitter assembly into the ignition key cylinder, turn the ignition switch from off to ON and wait at least 20 seconds.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-

Related Data List and Active Test 
DTC No.
Data List and Active Test
B2784
Antenna Coil Status

WIRING DIAGRAM


B329324E31


INSPECTION PROCEDURE

NOTICE:
  1. If the transponder key ECU assembly is replaced, refer to Service Bulletin.
  2. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Perform "DTC Output Confirmation Operation" procedure.

  1. Check for DTCs (Click here).

    OK:
    DTC B2784 is not output.

    Result:
    Result
    Proceed to
    B2784 is not output
    A
    B2784 is output
    B



B
Go to step 3
A

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK CONNECTION OF CONNECTOR
  1. Check that the connector is properly connected to the transponder key coil.


NEXT


4.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


5.CHECK FOR DTC
  1. Perform "DTC Output Confirmation Operation" procedure.

  1. Check for DTCs. (Click here).

    OK:
    DTC B2784 is not output.

    Result:
    Result
    Proceed to
    B2784 is not output
    A
    B2784 is output
    B



B
Go to step 6
A

END (CONNECTOR WAS NOT CONNECTED PROPERLY) 

6.CHECK TRANSPONDER KEY COIL (OUTPUT)


  1. Using an oscilloscope, check the waveform.


    B329326E15


    OK:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    I191-1 (ANT1) - Body ground
    Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform 1)
    I191-5 (ANT2) - Body ground
    Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform 2)

    OK:
    Waveform is similar to that shown in the illustration.


    Text in Illustration 
    *a
    Component with harness connected
    (Transponder Key Coil)
    *b
    Waveform 1
    *c
    Waveform 2
    -
    -

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 8
A


7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY COIL)
  1. Disconnect the I19 transponder key ECU assembly connector.

  1. Disconnect the I191 transponder key coil connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-4 (ANT1) - I191-1 (ANT1)
    Always
    Below 1 Ω
    I19-15 (ANT2) - I191-5 (ANT2)
    Always
    Below 1 Ω
    I19-4 (ANT1) or I191-1 (ANT1) - Body ground
    Always
    10 kΩ or higher
    I19-15 (ANT2) or I191-5 (ANT2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Temporarily replace the transponder key ECU assembly with a new one.

    HINT:
    Refer to Service Bulletin.

    NOTICE:
    Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.


NEXT


9.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


10.CHECK FOR DTC
  1. Perform "DTC Output Confirmation Operation" procedure.

  1. Check for DTCs (Click here).

    OK:
    DTC B2784 is not output.

    Result:
    Result
    Proceed to
    B2784 is not output
    A
    B2784 is output
    B



B
REPLACE TRANSPONDER KEY COIL (Click here)
A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)