WATER PUMP > INSTALLATION |
| 1. INSTALL ENGINE WATER PUMP ASSEMBLY |
![]() |
Install a new gasket and the engine water pump assembly together with the water pump pulley with the 16 bolts.
| 2. INSTALL WATER PUMP PULLEY |
Temporarily install the water pump pulley with the 4 bolts.
![]() |
Using SST, hold the water pump pulley.
| *1 | Union Nut Wrench |
| *a | 170 mm |
Using SST and union nut wrench, tighten the 4 bolts.
| 3. INSTALL WATER INLET HOUSING |
Install 2 new O-rings.
Install the water inlet housing with the 2 bolts and nut.
Connect the water hose.
| 4. INSTALL V-RIBBED BELT TENSIONER PULLEY |
![]() |
Install the V-ribbed belt tensioner pulley and dust shield with the bolt.
| *1 | Dust Shield |
| *2 | Pulley |
| *a | Correct |
| *b | Incorrect |
Install the 5 mm bi-hexagon wrench.
| 5. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY |
Install the idler pulley cover plate, No. 2 idler pulley sub-assembly and No. 2 idler pulley cover plate with the bolt.
| 6. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH |
Temporarily install the front No. 1 engine mounting bracket LH with the 6 bolts.
![]() |
Fully tighten the 5 bolts.
![]() |
Using SST, fully tighten the bolt.
| *a | 150 mm |
| 7. INSTALL ENGINE MOVING CONTROL ROD BRACKET |
![]() |
When replacing the engine moving control rod.
Install the engine moving control rod bracket with engine moving control rod with the 4 bolts.
Tighten the bolt E.
![]() |
When not replacing the engine moving control rod.
Install the engine moving control rod bracket with engine moving control rod with the 4 bolts.
| 8. INSTALL NO. 2 ENGINE MOUNTING STAY RH (for Intake Manifold Side) |
Install the No. 2 engine mounting stay RH with the bolt.
| 9. INSTALL NO. 2 ENGINE MOUNTING STAY RH (for Engine Mounting stay Side) |
Install the No. 2 engine mounting stay RH with the bolt.
Tighten the 2 nuts.
| 10. CONNECT NO. 2 RADIATOR HOSE |
Connect the No. 2 radiator hose with the hose clip.
| 11. INSTALL V-RIBBED BELT |
| 12. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Close the cylinder block drain cock plug (for Bank 1).
Close the cylinder block drain cock plug (for Bank 2, w/ Cylinder Block Drain Cock Plug).
Loosen the air drain cock plug on the water inlet housing.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until engine coolant overflows from the air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.
![]() |
Slowly fill the radiator assembly with TOYOTA Super Long Life Coolant (SLLC).
| *a | Code Mark |
| Code Mark "K" | 8.8 liters (9.3 US qts, 7.7 Imp. qts) |
| Code Mark "J" | 8.9 liters (9.4 US qts, 7.8 Imp. qts) |
Remove the reserve tank cap.
Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the engine coolant.
If the engine coolant level is low, add engine coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 13. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.