Home › Engine / Hybrid System ยท 2GR-FE › LUBRICATION › OIL AND OIL FILTER

OIL AND OIL FILTER > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with engine oil will result in removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. Skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
  3. In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.



1. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the oil into a container.

  1. Clean the oil drain plug.

  1. Install the oil drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



2. REMOVE OIL FILTER CAP ASSEMBLY


    A204919E01
  1. Connect the hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose



    A127997
  1. Remove the oil filter drain plug from the oil filter cap.



    A160741E02
  1. Insert the pipe with the hose into the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    O-ring
    *3
    Pipe

    NOTICE:
    Be sure to insert the pipe with the O-ring installed on the oil filter cap.

    HINT:
    Place the hose end into a container before draining oil from the hose.



    A127999
  1. Make sure that oil is completely drained, and remove the pipe and O-ring.

    HINT:
    Be sure to turn the pipe in the direction of the arrow to remove it.



    A128000E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  



    A128001E06
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    Oil Filter Cap
    *3
    O-ring

    NOTICE:
    Do not use any tools to remove the O-ring in order to prevent the cap from being damaged. Be sure to remove it by hand.



3. INSTALL OIL FILTER CAP ASSEMBLY
  1. Clean the inside of the oil filter cap, threads and O-ring groove.



    A128001E06
  1. Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    Oil Filter Cap
    *3
    O-ring

    NOTICE:
    Make sure that the O-ring does not get twisted on the groove.

  1. Install a new oil filter element to the oil filter cap.

  1. Remove all dirt and foreign matter from the installation surface and the inside of the cap on the engine side.

  1. Apply a light coat of engine oil to the O-ring again and install the oil filter cap.

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



    A128002E02
  1. Using SST, install the oil filter cap.
    Text in Illustration 
    *a
    No Clearance

    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Make sure that there is no clearance between the parts after tightening the oil filter cap.



    A161390E03
  1. Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Remove all dirt and foreign matter from the installation surface.

  1. Install the oil filter drain plug to the oil filter cap.

    Torque:
    13 N*m{ 127 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



4. ADD ENGINE OIL
  1. Add clean engine oil and install the oil filler cap.

    NOTICE:

    1. A308107
      Do not allow engine oil adhere to the moving parts of the belt tensioner, as this may cause malfunctions.
      If engine oil is on the location indicated by the arrow, replace the belt tensioner.


    Standard Oil Grade:

    Oil Grade
    Oil Viscosity (SAE)
    1. API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
    1. 0W-20
    1. 5W-20
    1. 5W-30
    1. 10W-30
    1. API grade SL, SM or SN multigrade engine oil
    1. 15W-40
    1. 20W-50


    Standard Capacity:

    Item
    Standard Condition
    Drain and refill with oil filter change
    6.1 liters (6.4 US qts, 5.4 lmp. qts)
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 lmp. qts)
    Dry fill
    6.8 liters (7.2 US qts, 6.0 lmp. qts)



5. INSPECT FOR OIL LEAK


6. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine, stop it and wait 5 minutes. The oil level should be between the engine oil level dipstick low level mark and full level mark.
    If the engine oil level is low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not add engine oil to above the full level mark.