Home › Engine / Hybrid System ยท 2AR-FE › FUEL › FUEL TANK (for TMMK Made)

FUEL TANK (for TMMK Made) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 FUEL TANK CUSHION


    A254966
  1. Install 5 new No. 1 fuel tank cushions as shown in the illustration.



2. INSTALL FUEL TANK BREATHER HOSE


    A347589E01
  1. Install the fuel tank breather hose to the fuel tank sub-assembly and slide the clip to secure it.
    Text in Illustration 
    *a
    Up
    *b
    120°
    *c
    2 to 7 mm (0.0787 to 0.276 in.)
    *d
    0 to 3 mm (0 to 0.118 in.)

    HINT:
    Engage the clip within the area shown in the illustration.



3. INSTALL NO. 1 FUEL TUBE CLAMP
  1. Install the No. 1 fuel tube clamp to the fuel tank sub-assembly.



4. INSTALL CHARCOAL CANISTER OUTLET HOSE
  1. Engage the No. 2 fuel tube clamp to install charcoal canister outlet hose to the fuel tank sub-assembly.



5. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY
  1. Engage the clamp to install the fuel tank main tube sub-assembly to the fuel tank sub-assembly.



6. INSTALL FUEL TANK SUB-ASSEMBLY
  1. Set the fuel tank sub-assembly on an engine lifter.

    HINT:
    Using height adjustment attachments and plate lift attachments, keep the fuel tank sub-assembly horizontal.

  1. Using the engine lifter, slowly raise the fuel tank sub-assembly, and then install the fuel tank sub-assembly, 2 fuel tank bands with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }

    NOTICE:
    1. Be careful not to drop the fuel tank assembly.
    2. When installing the fuel tank sub-assembly, tilt it slightly to prevent it from interfering with the surrounding parts.



7. CONNECT FUEL TANK TO FILLER PIPE HOSE


    A283935E03
  1. Push the fuel tank to filler pipe hose to the fuel tank sub-assembly and push in the retainer to engage the lock claws.
    Text in Illustration 
    *a
    Retainer
    *b
    Up
    *c
    90°
    *d
    120° (Retainer Area)
    V100135
    Push
    V100136
    Push in

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected parts of the fuel tank to filler pipe hose connector and fuel tank sub-assembly before performing this work.
    2. After connecting the fuel tank to filler pipe hose, check that the fuel tank to filler pipe hose is securely connected by pulling on the fuel tank to filler pipe hose connector.

    HINT:
    Make sure the retainer of the fuel tank to filler pipe hose is within the area shown in the illustration.



8. CONNECT FUEL TANK BREATHER HOSE
  1. Connect the fuel tank breather hose and slide the clip to secure it.



9. CONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE


    A283930E02
  1. Connect the No. 1 charcoal canister outlet hose and slide the clip to secure it.
    Text in Illustration 
    *1
    Fuel Emission Hose
    *2
    No. 1 Charcoal Canister Outlet Hose
    *a
    Up
    *b
    120°

    HINT:
    Engage the clip within the area shown in the illustration.



10. CONNECT FUEL EMISSION HOSE
  1. Connect the fuel emission hose and slide the clip to secure it.



11. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

NOTICE:
Check that there is no damage or foreign matter on the connecting parts of the fuel lines.



    A254956E04
  1. Connect the fuel tank main tube sub-assembly.
    Text in Illustration 
    *a
    Retainer
    *b
    Fuel Tube Connector
    *c
    Nylon Tube
    *d
    O-ring
    *e
    Fuel Pipe
    *f
    Claw
    V100135
    Push
    V100136
    Push in

    1. Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.

    2. Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.



12. INSTALL NO. 1 FUEL TANK PROTECTOR
  1. Install the No. 1 fuel tank protector to the fuel tank sub-assembly with the 3 clips.



13. INSTALL REAR NO. 1 STABILIZER BAR BRACKET
  1. Install the 2 rear No. 1 stabilizer bar brackets with the 4 nuts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



14. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
  1. Install the No. 3 parking brake cable assembly with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



15. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY
  1. Install the No. 2 parking brake cable assembly with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



16. INSTALL NO. 1 FLOOR UNDER COVER
  1. Install the No. 1 floor under cover with the 2 bolts, 3 nuts, screw and 2 clips.

    Torque:
    Bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    Nut:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



17. INSTALL NO. 2 FLOOR UNDER COVER
  1. Install the No. 2 floor under cover with the 2 bolts, 3 nuts, screw and 2 clips.

    Torque:
    Bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    Nut:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



18. INSTALL CENTER EXHAUST PIPE ASSEMBLY



19. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
(Click here)


20. ADD FUEL


21. INSPECT FOR EXHAUST GAS LEAK