Home › Drivetrain ยท DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 2GR-FE)

FRONT DRIVE SHAFT ASSEMBLY (for 2GR-FE) > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
  1. Hold the drive shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C108564
  1. Using pliers, remove the front No. 2 axle inboard joint boot clamp.



2. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP

HINT:
Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.



3. SEPARATE FRONT AXLE INBOARD JOINT BOOT
  1. Separate the front axle inboard joint boot from the front drive inboard joint assembly.



4. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Remove the old grease from the front drive inboard joint assembly.



    F045461E24
  1. Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Do not use a punch for the marks.

  1. Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.

  1. Hold the drive shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    F045046
  1. Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.



    C141145E15
  1. Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Do not use a punch for the marks.

  1. Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.

    NOTICE:
    1. Do not tap the rollers.
    2. Do not drop the tripod joint.



5. REMOVE FRONT AXLE INBOARD JOINT BOOT
  1. Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.



6. REMOVE FRONT DRIVE SHAFT DAMPER


    C292475
  1. Using needle-nose pliers, separate the 2 front drive shaft damper clamps as shown in the illustration.

  1. Remove the front drive shaft damper and 2 front drive shaft damper clamps from the front drive outboard joint shaft assembly.



7. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP


    C081167
  1. Using pliers, remove the front No. 2 axle outboard joint boot clamp.



8. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:
Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.



9. REMOVE FRONT AXLE OUTBOARD JOINT BOOT
  1. Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.

  1. Remove the grease from the outboard joint.



10. REMOVE FRONT DRIVE SHAFT DUST COVER LH


    F040647E07
  1. Using SST and a press, remove the front drive shaft dust cover LH.

    SST
    09950-00020  

    NOTICE:
    1. Be careful not to drop the front drive inboard joint assembly.
    2. Do not overtighten SST.



11. REMOVE FRONT DRIVE SHAFT DUST COVER RH


    C067101
  1. Using a press, remove the front drive shaft dust cover RH.

    NOTICE:
    Be careful not to drop the front drive inboard joint assembly.



12. REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side)


  1. w/ Cover:



      F040208E03
    1. Using SST and a press, remove the front drive shaft dust cover.

      SST
      09950-00020  

      NOTICE:
      1. Be careful not to drop the front drive inboard joint assembly.
      2. Do not overtighten SST.

      HINT:
      If the front drive shaft dust cover is removed, it is not necessary to reinstall it.



13. REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)


    C092033
  1. Using a snap ring expander, remove the drive shaft hole snap ring.



    F040210E04
  1. Using SST and a press, remove the front drive shaft bearing.

    SST
    09527-10011  

    NOTICE:
    Be careful not to drop the front drive inboard joint assembly.