Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for TMC, TMMR Made)

HEADLIGHT ASSEMBLY (for TMC, TMMR Made) > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. INSTALL GROMMET


    E301886
  1. Install the grommet.



2. INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING
  1. Install a new headlight leveling motor base packing.



3. INSTALL HEADLIGHT LEVELING MOTOR (w/o AFS)


    E301883E01
  1. Insert the headlight leveling motor in the direction indicated by the arrow (1) shown in the illustration.
    Text in Illustration 
    *a
    Aiming Screw

  1. Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (2) shown in the illustration to engage the shaft.

    HINT:
    Turn the aiming screw the same number of times as it was turned during removal.



    E301881E01
  1. Turn the headlight leveling motor in the direction indicated by the arrow (3) shown in the illustration and engage the pin to install the headlight leveling motor to the headlight unit.
    Text in Illustration 
    *a
    Aiming Screw

    HINT:
    When installing the headlight leveling motor of the headlight assembly RH, turn the headlight leveling motor in the opposite direction indicated by the arrow (3) shown in the illustration.

  1. Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (4) shown in the illustration.

    HINT:
    Turn the aiming screw the same number of times as it was turned during removal.



4. INSTALL HEADLIGHT LEVELING MOTOR (w/ AFS)


    E191797
  1. Engage the tip of the headlight leveling motor with the reflector as shown in the illustration.



    E301885
  1. Turn the headlight leveling motor as shown in the illustration and engage the pin to install the headlight leveling motor to the headlight unit.

    HINT:
    For the headlight leveling motor RH, rotate it symmetrical to the directional arrow shown in the illustration.



5. INSTALL FRONT TURN SIGNAL LIGHT BULB
  1. Install the front turn signal light bulb to the front turn signal light socket.



    E301879
  1. Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to install them as a unit.



6. INSTALL HEADLIGHT SOCKET COVER
  1. for Halogen Headlight:

    1. Install the 2 headlight socket covers to the headlight unit.

  1. for HID Headlight:

    1. Install the headlight socket cover to the headlight unit.



7. INSTALL NO. 2 HEADLIGHT BULB (for Halogen Headlight)


    E301871
  1. Turn the No. 2 headlight bulb as shown in the illustration to install it.

    NOTICE:
    Do not touch the bulb glass.



8. INSTALL DISCHARGE HEADLIGHT BULB (for HID Headlight)
  1. Set the discharge headlight bulb to the headlight unit.

    NOTICE:
    Do not touch the bulb glass.



    E301877E01
  1. Lock the set spring to install the discharge headlight bulb as indicated by arrows, in the order shown in the illustration.



9. INSTALL HEADLIGHT LIGHT CONTROL ECU SUB-ASSEMBLY (for HID Headlight)


    E303119E01
  1. Turn the socket of the headlight light control ECU sub-assembly as shown in the illustration to connect it.
    Text in Illustration 
    *a
    Red Line

    NOTICE:
    1. Check that the O-ring is installed on the headlight light control ECU sub-assembly.
    2. Check that the O-ring is not damaged or contaminated with foreign matter. If there is any damage, replace the O-ring with a new one.
    3. Do not pull the headlight light control ECU sub-assembly with the socket connected.

  1. Check that the red line on the output harness is not twisted and store the harness in the headlight assembly securely so that the output harness is not pinched.



    E303120E01
  1. Turn the headlight light control ECU sub-assembly as shown in the illustration until the lock marks are aligned to install it.
    Text in Illustration 
    *a
    Lock Mark

    NOTICE:
    1. To prevent incomplete installation, make sure to fully push in and turn the headlight light control ECU sub-assembly until the lock marks are aligned.
    2. Do not apply excessive force using a tool.



10. INSTALL NO. 1 HEADLIGHT BULB


    E301869
  1. Turn the No. 1 headlight bulb in the direction indicated by the arrow shown in the illustration to install it.

    NOTICE:
    Do not touch the bulb glass.



11. INSTALL HEADLIGHT COVER


    E301888
  1. Engage the 8 guides and 2 claws.



    E301887
  1. Install the headlight cover with the 3 screws.

    Torque:
    1.3 N*m{ 13 kgf*cm , 11 in.*lbf }