Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > INSPECTION

for Preparation Click here


NOTICE:
When using a vise, do not overtighten it.



1. INSPECT PRELOAD (for Manual Tilt and Manual Telescopic Steering Column)


    C239332E01
  1. Secure the steering column assembly in a vise using aluminum plates as shown in the illustration.
    Text in Illustration 
    *1
    Aluminum Plate
    *2
    Wooden Block

    NOTICE:
    1. Do not overtighten the vise, as the steering column assembly may become deformed.
    2. Support the steering column assembly with a wooden block or similar item to ensure that it does not fall.



    C220801E02
  1. Install the 2 service nuts to the steering main shaft.
    Text in Illustration 
    *1
    Service Nut

    Recommended Service Nut:
    Thread Diameter:
    12.0 mm (0.472 in.)
    Thread Pitch:
    1.25 mm (0.0492 in.)

  1. Simultaneously rotate the service nut that was installed first counterclockwise and rotate the service nut that was installed second clockwise to lock them.

    NOTICE:
    Do not apply excessive torque to the service nuts by using a tool such as an impact wrench.

    HINT:
    These nuts are installed to turn the steering main shaft. They should be removed after inspecting the steering main shaft rotating torque.



    C239349
  1. Using a torque wrench, turn the main shaft and measure the preload.

    Torque:
    Preload:
    1.0 to 1.8 N*m{ 11 to 18 kgf*cm , 9 to 15 in.*lbf }

    If the preload is not as specified, replace the power steering ECU with motor assembly or electric power steering column sub-assembly with a new one.



2. INSPECT PRELOAD (for Power Tilt and Power Telescopic Steering Column)


    C239729E01
  1. Securely set the steering column assembly on a wooden block or similar item.
    Text in Illustration 
    *1
    Wooden Block

    NOTICE:
    Be sure to hold the steering column assembly by hand so that it will not move while servicing.



    C220801E02
  1. Install the 2 service nuts to the steering main shaft.
    Text in Illustration 
    *1
    Service Nut

    Recommended Service Nut:
    Thread Diameter:
    12.0 mm (0.472 in.)
    Thread Pitch:
    1.25 mm (0.0492 in.)

  1. Simultaneously rotate the service nut that was installed first counterclockwise and rotate the service nut that was installed second clockwise to lock them.

    NOTICE:
    Do not apply excessive torque to the service nuts by using a tool such as an impact wrench.

    HINT:
    These nuts are installed to turn the steering main shaft. They should be removed after inspecting the steering main shaft rotating torque.



    C241119
  1. Using a torque wrench, turn the main shaft and measure the preload.

    Torque:
    Preload:
    1.0 to 1.8 N*m{ 11 to 18 kgf*cm , 9 to 15 in.*lbf }

    If the preload is not as specified, replace the power steering ECU with motor assembly or electric power steering column sub-assembly with a new one.



3. INSPECT STEERING LOCK OPERATION (w/o Smart Entry and Start System)


    C239701
  1. Check that the steering lock mechanism is activated when the key is removed.



    C239702E01
  1. Check that the steering lock mechanism is deactivated when the key is inserted and turned to the ACC position.
    Text in Illustration 
    *a
    LOCK
    *b
    ACC
    If there is any abnormality, replace the ignition switch lock cylinder assembly or steering column upper bracket assembly with a new one.



4. INSPECT STEERING COLUMN ASSEMBLY


    C232487E01
  1. Check that the 2 capsules are securely installed to the steering column assembly as shown in the illustration.

    Minimum Dimension:
    A
    B
    1 mm (0.0394 in.)
    12 mm (0.473 in.)

    Text in Illustration 
    *1
    Capsule
    If the capsules are not positioned as specified, replace the electric power steering column sub-assembly with a new one.

  1. Check the 2 capsules for deformation and damage.
    If either of the capsules is deformed, loose, missing or damaged, replace the electric power steering column sub-assembly with a new one.



5. INSPECT TILT MOTOR


    C197978E08
  1. Apply 12 V battery voltage to the tilt motor connector.

  1. Then check the steering wheel tilt operation.

    OK:
    Measurement Condition
    Specified Condition
    1. 12 V battery positive (+) lead → Terminal 1 (TIM-)
    2. 12 V battery negative (-) lead → Terminal 2 (TIM+)
    The steering wheel tilts down.
    1. 12 V battery positive (+) lead → Terminal 2 (TIM+)
    2. 12 V battery negative (-) lead → Terminal 1 (TIM-)
    The steering wheel tilts up.

    Text in Illustration 
    *a
    Component without harness connected
    (Tilt Motor)



6. INSPECT TELESCOPIC MOTOR


    C197978E09
  1. Apply 12 V battery voltage to the telescopic motor connector.

  1. Then check the steering column telescopic operation.

    OK:
    Measurement Condition
    Specified Condition
    1. 12 V battery positive (+) lead → Terminal 2 (TEM+)
    2. 12 V battery negative (-) lead → Terminal 1 (TEM-)
    The steering column contracts.
    1. 12 V battery positive (+) lead → Terminal 1 (TEM-)
    2. 12 V battery negative (-) lead → Terminal 2 (TEM+)
    The steering column extends.

    Text in Illustration 
    *a
    Component without harness connected
    (Telescopic Motor)