Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for TMMK Made)

DTC    B1656/38    Seat Belt Buckle Switch LH Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat belt buckle switch LH circuit consists of the airbag sensor assembly and front seat inner belt assembly LH.
DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1656/38
  1. The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat belt buckle switch LH circuit.
  2. Front seat inner belt assembly LH malfunction
  3. Airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat inner belt assembly LH (Seat belt buckle switch LH)
  3. Airbag sensor assembly

WIRING DIAGRAM


C239223E13


INSPECTION PROCEDURE

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK CONNECTORS
  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly LH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


2.CHECK FLOOR WIRE (OPEN)


    C238406E05
  1. Using a service wire, connect terminals 10 (LBE+) and 18 (LBE-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N43-2 (LBE+) - N43-1 (LBE-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (SHORT)
C238407E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N43-2 (LBE+) - N43-1 (LBE-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (SHORT TO B+)


    C238407E05
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    N43-2 (LBE+) - Body ground
    Engine switch on (IG)
    Below 1 V
    N43-1 (LBE-) - Body ground
    Engine switch on (IG)
    Below 1 V

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT TO GROUND)


    C238407E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N43-2 (LBE+) - Body ground
    Always
    1 MΩ or higher
    N43-1 (LBE-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)



NG
REPLACE FLOOR WIRE
OK


6.CHECK DTC


    C238328E01
  1. Connect the connectors to the airbag sensor assembly and front seat inner belt assembly LH.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656/38 is not output.

    HINT:
    Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Airbag Sensor Assembly



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK FRONT SEAT INNER BELT ASSEMBLY LH


    C238328E01
  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Replace the front seat inner belt assembly LH with a known good one (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1656/38 is not output.

    HINT:
    Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Restore the front seat inner belt assembly LH that was installed for testing to its original location (Click here).
    Text in Illustration 
    *1
    Front Seat Inner Belt Assembly LH
    *2
    Airbag Sensor Assembly



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)