DTC B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1656/38 |
|
|

| 1.CHECK CONNECTORS |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly LH.
Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 10 (LBE+) and 18 (LBE-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N43-2 (LBE+) - N43-1 (LBE-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N43-2 (LBE+) - N43-1 (LBE-) | Always | 1 MΩ or higher |
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N43-2 (LBE+) - Body ground | Engine switch on (IG) | Below 1 V |
| N43-1 (LBE-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N43-2 (LBE+) - Body ground | Always | 1 MΩ or higher |
| N43-1 (LBE-) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 6.CHECK DTC |
![]() |
Connect the connectors to the airbag sensor assembly and front seat inner belt assembly LH.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
|
| ||||
| OK | ||
| ||
| 7.CHECK FRONT SEAT INNER BELT ASSEMBLY LH |
![]() |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Replace the front seat inner belt assembly LH with a known good one (Click here).
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Restore the front seat inner belt assembly LH that was installed for testing to its original location (Click here).
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
|
| ||||
| OK | ||
| ||