WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System) > TERMINALS OF ECU |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |

Disconnect the MB, I12 and I13 main body ECU (multiplex network body ECU) connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| MB-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| I12-3 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| MB-30 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | ignition switch ACC | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | ignition switch off | Below 1 V |
| MB-31 (ALTB) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-32 (IG) - Body ground | - | IG power supply | ignition switch ON | 11 to 14 V |
| MB-32 (IG) - Body ground | - | IG power supply | ignition switch off | Below 1 V |
| I13-17 (KSW) - Body ground | G - Body ground | Unlock warning switch signal | No key in ignition key cylinder | 10 kΩ or higher |
| I13-17 (KSW) - Body ground | G - Body ground | Unlock warning switch signal | Key in ignition key cylinder | Below 1 Ω |
Reconnect the MB, I12 and I13 main body ECU (multiplex network body ECU) connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| 3B-8 (ACT-) - Body ground | V - Body ground | Door lock motor unlock drive output (except driver door) | Door control switch (multiplex network master switch) or driver door key cylinder off | Below 1 V |
| 3B-8 (ACT-) - Body ground | V - Body ground | Door lock motor unlock drive output (except driver door) | Door control switch (multiplex network master switch) or driver door key cylinder unlocked | 11 to 14 V |
| 3B-3 (ACT+) - Body ground | W - Body ground | Door lock motor lock drive output (all doors) | Door control switch (multiplex network master switch) or driver door key cylinder off | Below 1 V |
| 3B-3 (ACT+) - Body ground | W - Body ground | Door lock motor lock drive output (all doors) | Door control switch (multiplex network master switch) or driver door key cylinder locked | 11 to 14 V |
| 3B-4 (ACTD) - Body ground | GR - Body ground | Driver door lock motor unlock drive output | Door control switch (multiplex network master switch) or driver door key cylinder off | Below 1 V |
| 3B-4 (ACTD) - Body ground | GR - Body ground | Driver door lock motor unlock drive output | Door control switch (multiplex network master switch) or driver door key cylinder unlocked | 11 to 14 V |
| 3C-15 (FLCY) - Body ground | L - Body ground | Front door LH courtesy light switch input | Front door LH open | Below 1 V |
| 3C-15 (FLCY) - Body ground | L - Body ground | Front door LH courtesy light switch input | Front door LH closed | 11 to 14 V |
| I13-19 (FRCY) - Body ground | Y - Body ground | Front door RH courtesy light switch input | Front door RH open | Below 1 V |
| I13-19 (FRCY) - Body ground | Y - Body ground | Front door RH courtesy light switch input | Front door RH closed | 11 to 14 V |
| I13-1 (LCTY) - Body ground | P - Body ground | Rear door LH courtesy light switch input | Rear door LH open | Below 1 V |
| I13-1 (LCTY) - Body ground | P - Body ground | Rear door LH courtesy light switch input | Rear door LH closed | Pulse generation |
| I13-6 (RCTY) - Body ground | B - Body ground | Rear door RH courtesy light switch input | Rear door RH open | Below 1 V |
| I13-6 (RCTY) - Body ground | B - Body ground | Rear door RH courtesy light switch input | Rear door RH closed | Pulse generation |
| I13-7 (LSFL) - Body ground | V - Body ground | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V |
| I13-7 (LSFL) - Body ground | V - Body ground | Front door LH unlock detection switch input | Front door LH locked | Pulse generation |
| I13-18 (LSFR) - Body ground | W - Body ground | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V |
| I13-18 (LSFR) - Body ground | W - Body ground | Front door RH unlock detection switch input | Front door RH locked | Pulse generation |
| 3A-53 (LSR) - Body ground | Y - Body ground | Rear door RH unlock detection switch input | Rear door RH or LH unlocked | Below 1 V |
| 3A-53 (LSR) - Body ground | Y - Body ground | Rear door RH unlock detection switch input | Ignition switch off, all doors closed and rear door RH and LH locked | Pulse generation |
| 3C-17 (LSR) - Body ground | LG - Body ground | Rear door LH unlock detection switch input | Rear door LH or RH unlocked | Below 1 V |
| 3C-17 (LSR) - Body ground | LG - Body ground | Rear door LH unlock detection switch input | Ignition switch off, all doors closed and rear door LH and RH locked | Pulse generation |
| 2D-22 (BZR) - Body ground | BE - Body ground | Wireless door lock buzzer signal | Wireless door lock buzzer off | Below 1 V |
| 2D-22 (BZR) - Body ground | BE - Body ground | Wireless door lock buzzer signal | Wireless door lock buzzer on | Pulse generation |
| I13-4 (PRG) - Body ground | P - Body ground | Signal output to door control receiver | Key inserted in ignition key cylinder → key pulled out of ignition key cylinder | 11 to 14 V → Pulse generation → 11 to 14 V |
| I13-16 (RDA) - Body ground | L - Body ground | Signal input from door control receiver | Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch pressed | Pulse generation | |||
| I13-17 (KSW) - Body ground | G - Body ground | Key unlock warning switch input | No key in ignition key cylinder | Pulse generation |
| I13-17 (KSW) - Body ground | G - Body ground | Key unlock warning switch input | Key in ignition key cylinder | Below 1 V |
| CHECK DOOR CONTROL RECEIVER |

Disconnect the O24 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| O24-5 (+B) - Body ground | W - Body ground | Battery (power supply) | Always | 11 to 14 V |
| O24-1 (GND) - Body ground | B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the O24 door control receiver connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| O24-3 (PRG) - O24-1 (GND) | P - BR | Signal input from main body ECU (multiplex network body ECU) | Key inserted in ignition key cylinder → key pulled out of ignition key cylinder | 11 to 14 V → Pulse generation → 11 to 14 V |
| O24-2 (RDA) - O24-1 (GND) | L - BR | Signal output to main body ECU (multiplex network body ECU) | Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch pressed | Pulse generation |