Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE COMPARTMENT DOOR (for TMMK Made)

LUGGAGE COMPARTMENT DOOR (for TMMK Made) > DISASSEMBLY

for Preparation Click here



1. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    B380679
  1. Remove the 13 clips and luggage compartment door cover.



2. REMOVE LUGGAGE COMPARTMENT DOOR CUSHION


    B380680
  1. Disengage the 4 claws and remove the 4 luggage compartment door cushions.



3. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH


    B380681
  1. Remove the 2 clips.

  1. Disengage the clip and remove the luggage compartment door hinge cover LH.



4. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER RH

HINT:
Use the same procedure as for the LH side.



5. REMOVE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
  1. Disconnect the connector.



    B386472
  1. Remove the 2 bolts and disengage the luggage compartment door lock assembly.



    B386473
  1. Disengage the claw as shown in the illustration.



    B386474
  1. Disengage the luggage door lock control cable sub-assembly and remove the luggage compartment door lock assembly.



6. REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

HINT:
When removing the rear spoiler, heat the vehicle body and rear spoiler sub-assembly using a heat light.

Heating Temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Rear Spoiler Sub-assembly
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body, rear spoiler sub-assembly excessively.



    B380991
  1. Apply protective tape around the rear spoiler sub-assembly as shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B380992
  1. Remove the 2 nuts.



  1. Insert a piano wire between the vehicle body and rear spoiler sub-assembly.


    B380993E01


    Text in Illustration 
    *a
    Wooden Block
    *b
    Piano Wire
    *c
    Double-sided Tape
    *d
    Clip
    *e
    Stud Bolt
    -
    -

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

  1. Pull the piano wire and scrape off the double-sided tape that holds the rear spoiler sub-assembly to the vehicle body.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Disengage the 4 clips and remove the rear spoiler sub-assembly.

  1. Remove the 4 clips from the rear spoiler cover.

  1. Remove the 2 gaskets from the rear spoiler cover.

  1. Remove the 2 stud bolts from the rear spoiler cover.



7. REMOVE REAR LIGHT ASSEMBLY LH


    E300989
  1. Disconnect the connector.

  1. Remove the 4 nuts and rear light assembly.



8. REMOVE REAR LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



9. REMOVE LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH SUB-ASSEMBLY
  1. Disconnect the 2 connectors.



    B401892
  1. Remove the 6 nuts.



    B381029
  1. Apply protective tape around the luggage compartment door outside garnish sub-assembly as shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B381010
  1. Disengage the 4 clips to remove the luggage compartment door outside garnish sub-assembly.

  1. Remove the 4 clips from the luggage compartment door outside garnish.

  1. Remove the 6 gaskets from the luggage compartment door outside garnish.



10. REMOVE LICENSE PLATE LIGHT ASSEMBLY LH


    E226675
  1. Disconnect the connector.

  1. Disengage the 2 claws and remove the license plate light assembly.



11. REMOVE LICENSE PLATE LIGHT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.