Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE COMPARTMENT DOOR (for TMMK Made)

LUGGAGE COMPARTMENT DOOR (for TMMK Made) > REASSEMBLY

for Preparation Click here



1. INSTALL LICENSE PLATE LIGHT ASSEMBLY LH
  1. Engage the 2 claws to install the license plate light assembly.

  1. Connect the connector.



2. INSTALL LICENSE PLATE LIGHT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



3. INSTALL LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH SUB-ASSEMBLY
  1. Install 6 new gaskets to the luggage compartment door outside garnish.

  1. Install 4 new clips to the luggage compartment door outside garnish.

  1. Engage the 4 clips.

  1. Install the luggage compartment door outside garnish sub-assembly with the 6 nuts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }

  1. Connect the 2 connectors.



4. INSTALL REAR LIGHT ASSEMBLY LH


    E300989E01
  1. Install the rear light assembly with the 4 nuts.

    Torque:
    Nut (A):
    4.1 N*m{ 42 kgf*cm , 36 in.*lbf }
    Nut (B):
    3.6 N*m{ 37 kgf*cm , 32 in.*lbf }

  1. Connect the connector.



5. INSTALL REAR LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



6. INSTALL REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

HINT:
When installing a new rear spoiler, heat the vehicle body and rear spoiler sub-assembly using a heat light.

Heating Temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Rear Spoiler Sub-assembly
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body, rear spoiler sub-assembly excessively.

  1. Install the 2 stud bolts to the rear spoiler cover.

  1. Install 2 new gaskets to the rear spoiler cover.

  1. Install 4 new clips to the rear spoiler cover.

  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any remaining double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Using a heat light, heat the vehicle body and a new rear spoiler sub-assembly.

  1. Remove the release paper from the rear spoiler sub-assembly.



    B401581
  1. Engage the 4 clips.

  1. Install the rear spoiler sub-assembly with the 2 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



7. INSTALL LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY
  1. Apply MP grease to the sliding parts of the luggage compartment door lock assembly.

  1. Engage the luggage door lock control cable sub-assembly.



    B386475
  1. Engage the claw as shown in the illustration.

  1. Install the luggage compartment door lock assembly with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



8. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER LH


    B380681
  1. Engage the clip.

  1. Install the luggage compartment door hinge cover LH with the 2 clips.



9. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL LUGGAGE COMPARTMENT DOOR CUSHION


    B380680
  1. Engage the 4 claws and install 4 new luggage compartment door cushions.



11. INSTALL LUGGAGE COMPARTMENT DOOR COVER


    B380679
  1. Install the luggage compartment door cover with the 13 clips.



12. ADJUST REAR TELEVISION CAMERA ASSEMBLY OPTICAL AXIS (w/ Parking Assist Monitor System)