Home › Power Source / Network ยท 2GR-FE BATTERY / CHARGING › GENERATOR

GENERATOR > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR DRIVE END FRAME BEARING


    A128081E01
  1. Using SST and a press, press in a new generator drive end frame bearing.

    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)



    A137712E04
  1. Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.
    Text in Illustration 
    *a
    Tab
    *b
    Cutout

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }



2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the drive end frame on the generator pulley with clutch.



    A118367E01
  1. Install the generator rotor assembly to the drive end frame.



3. INSTALL GENERATOR CLUTCH PULLEY
  1. Temporarily install the generator pulley with clutch onto the rotor shaft.

  1. Mount the generator drive end frame in a vise tightly.



    A128069E03
  1. Confirm SST (A) and (B) shown in the illustration.
    Text in Illustration 
    *1
    SST (A)
    *2
    SST (B)

    SST
    09820-63021  



    A185232E02
  1. Place the rotor shaft end into SST (A).
    Text in Illustration 
    *1
    Rotor Shaft
    *2
    SST (A)



    A185233E02
  1. Fit SST (B) to the generator pulley with clutch.
    Text in Illustration 
    *1
    Clutch Pulley
    *2
    SST (B)
    *3
    SST (A)



    A256114E02
  1. Tighten the pulley by turning SST (B) in the direction shown in the illustration.
    Text in Illustration 
    *1
    SST (B)
    *2
    SST (A)
    *a
    Fulcrum Length
    100 mm (3.94 in.)
    *b
    Fulcrum Length
    255 mm (10.04 in.)

    Torque:
    without SST:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }
    with SST:
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }

    NOTICE:
    1. The "with SST" torque value is effective when using SST with a fulcrum length of 100 mm (3.94 in.) and a torque wrench with a fulcrum length of 255 mm (10.04 in.) (Click here).
    2. The "with SST" torque value is effective when SST is parallel to the torque wrench.
    3. Check that the drive end frame is secured in the vise tightly.
    4. Hold SST (A) tightly during the operation.

  1. Remove SST from the generator assembly.

  1. Check that the generator pulley with clutch rotates smoothly.

  1. Install a new generator pulley cap to the generator pulley with clutch.



4. INSTALL GENERATOR COIL ASSEMBLY


    A118365E01
  1. Place a new generator washer on the generator rotor.



    A128082E05
  1. Using a deep socket wrench (21 mm) and a press, slowly press in the generator coil assembly.
    Text in Illustration 
    *1
    Deep Socket Wrench (21 mm)



    A128074
  1. Install the 4 bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }



5. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


    A079315E18
  1. While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the brush holder hole.
    Text in Illustration 
    *1
    Pin



    A079316E05
  1. Install the brush holder assembly to the generator coil with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Pull out the pin from the generator brush holder.
    Text in Illustration 
    *1
    Pin



6. INSTALL GENERATOR TERMINAL INSULATOR


    A128083E01
  1. Install the generator terminal insulator to the generator coil.

    NOTICE:
    Be sure to install the terminal insulator in the correct direction.



7. INSTALL GENERATOR REAR END COVER


    A128071
  1. Install the generator rear end cover to the generator coil with the 3 nuts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }