Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT DOOR WINDOW FRAME MOULDING (for TMMK Made)

FRONT DOOR WINDOW FRAME MOULDING (for TMMK Made) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING


    B381018
  1. Engage the claw and guide of the front door upper window frame moulding to the door frame.

  1. Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding with 7 new rivets.

    HINT:
    If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

    NOTICE:

    1. B125583E10
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
      Text in Illustration 
      *a
      Riveter
      *b
      Mandrel
      *c
      Incorrect

    2. B125584E11
      Confirm that the rivets are seated properly against the moulding.
      Text in Illustration 
      *a
      Riveter
      *b
      Incorrect
    3. Do not tilt the riveter when installing the rivet to the moulding.
    4. Do not leave any space between the rivet head and moulding.

    5. B125585E13
      Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.
      Text in Illustration 
      *a
      Riveter
      *b
      Incorrect



2. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:
When installing a new front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Front Door Rear Window Frame Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or front door rear window frame moulding excessively.

  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any remaining double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Using a heat light, heat the vehicle body and a new front door rear window frame moulding.

  1. Remove the release paper from the front door rear window frame moulding.

    HINT:
    After removing the release paper, keep the exposed adhesive free from foreign matter.



    B381016E01
  1. Engage the clip and guide, and attach the double-sided tape to install the front door rear window frame moulding.
    Text in Illustration 
    *a
    Caulking Sponge
    V100155
    Double-sided Tape



3. INSTALL FRONT DOOR WEATHERSTRIP


    B280376
  1. Engage the 19 clips and install the front door weatherstrip.



4. INSTALL FRONT DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door check assembly.

  1. Clean the bolt hole on the vehicle body.

  1. Clean the bolt threads of the bolt.

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    B280375E02
  1. Install the front door check assembly with the 3 bolts.

    Torque:
    Bolt (A):
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    Bolt (B):
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



5. INSTALL FRONT DOOR GLASS RUN


    B280345
  1. Install the front door glass run.



6. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY
(Click here)