Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR BELT MOULDING (for TMMK Made)

REAR DOOR BELT MOULDING (for TMMK Made) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B280387
  1. Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel plug as shown in the illustration.



4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B380656
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 3 guides.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



5. REMOVE REAR ARMREST ASSEMBLY


    B280391
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides to remove the rear armrest assembly.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B380658E01
  1. Apply protective tape to the rear door panel.
    Text in Illustration 
    *a
    Protective Tape



    B380659
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 8 clips.



    B380660E01
  1. Pull out the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Rear Door Inner Glass Weatherstrip
    *a
    Reference Boss

  1. Disengage the reference boss from the rear door panel.

  1. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    B380661
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.



    B280399E02
  1. Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver



7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B280398E02
  1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver



8. REMOVE REAR DOOR SERVICE HOLE COVER


    B380716
  1. Disconnect the connector.

  1. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through the rear door service hole cover.

  1. Remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the rear door panel.



9. REMOVE REAR DOOR CHECK ASSEMBLY


    B280406
  1. Remove the bolt and 2 nuts, and rear door check assembly.



10. REMOVE REAR DOOR WEATHERSTRIP


    B380664
  1. Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.



11. REMOVE REAR DOOR GLASS RUN


    B380665
  1. Remove the rear door glass run.



12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B380666
  1. Remove the 2 bolts and screw and rear door lower window frame sub-assembly.

    NOTICE:
    When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.



13. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B280410
  1. Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.



14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B380667
  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the rear door glass sub-assembly.



15. REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    B380984
  1. Apply protective tape around the rear door belt moulding assembly as shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B380985E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 6 claws to remove the rear door belt moulding assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver
    V100155
    Protective Tape