Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR (for TMMK Made)

OUTER REAR VIEW MIRROR (for TMMK Made) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B380633
  1. Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel plug as shown in the illustration.



2. REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER


    B380639
  1. Disengage the 2 claws and 2 guides to remove the front door front lower frame upper cover.



3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B380635
  1. Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides.

  1. Disconnect each connector to remove the power window regulator master switch assembly with front door armrest base panel.



4. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B401212
  1. Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides.

  1. Disconnect each connector to remove the power window regulator switch assembly with front door armrest base panel.



5. REMOVE FRONT ARMREST ASSEMBLY


    B277187
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides to remove the front armrest assembly.



6. REMOVE COURTESY LIGHT ASSEMBLY


    E226714E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side
    *1
    Protective Tape

  1. Disconnect the connector and remove the courtesy light assembly.



7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B380640E01
  1. Apply protective tape to the front door panel.
    Text in Illustration 
    *a
    Protective Tape



    B380641
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 10 clips.



    B380642E01
  1. Pull out the front door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Front Door Inner Glass Weatherstrip
    *a
    Reference Boss

  1. Disengage the reference boss from the front door panel.

  1. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.



    B380644
  1. Disengage the clamp.

  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly as shown in the illustration.



8. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    B380647E01
  1. Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver



9. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    B380648
  1. Disengage the 3 clips to remove the front door lower frame bracket garnish.



10. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


    B381033
  1. Remove the clip.



    B381034
  1. Disconnect the connector.

  1. Remove the 3 bolts.

  1. Disengage the claw.



    B381035
  1. Disengage the clip to remove the outer rear view mirror assembly.