FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > OPERATION CHECK |
| CHECK POWER SEAT FUNCTION |
![]() |
Check the basic functions.
| *1 | Slide Function |
| *2 | Reclining Function |
| *3 | Lifter Function |
| *4 | Front Vertical Function |
| *5 | Lumbar Support Adjustment Function |
Operate the power seat switches and check that each seat function operates properly:
| CHECK POWER SEAT MOTOR (SLIDING, FRONT VERTICAL, LIFTER AND RECLINING FUNCTIONS) |
Check the PTC operation inside the power seat motor.
Choose a power seat function. Operate a switch of the front power seat switch LH (w/ Memory) and move the seat to the farthest possible position in one direction. Keep the seat in that position for approximately 60 seconds.
Operate the switch of the front power seat switch LH (w/ Memory) again and continue to try to move the seat in the same direction as in the previous step. Measure the time until the current is shut off (motor operation sound will stop).
After the current is shut off, release the switch of the front power seat switch LH (w/ Memory) and wait for approximately 60 seconds.
Operate the same switch of the front power seat switch LH (w/ Memory) and move the seat in the opposite direction. Check that the motor operates.
| CHECK LUMBAR SUPPORT ADJUSTMENT MOTOR |
Check the PTC operation inside the lumbar support adjustment motor.
Operate the lumbar front power seat switch and move the lumbar support to either the foremost or rearmost position. Keep the seat in that position for approximately 60 seconds.
Operate the lumbar front power seat switch again and continue to try to move the lumbar support in the same direction as in the previous step. Measure the time until the current is shut off (motor operation sound will stop).
After the current is shut off, release the lumbar front power seat switch and wait for approximately 60 seconds.
Operate the lumbar front power seat switch and move the lumbar support in the opposite direction. Check that the motor operates.
| CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION |
![]() |
Turn the engine switch on (IG) and check that the P position indicator is on.
| *1 | M1 Switch |
| *2 | M2 Switch |
| *3 | SET Switch |
Move the seat to the foremost and uppermost positions using the front power seat switch LH (w/ Memory).
Check that the buzzer sounds for 0.5 seconds and the seat position is memorized when the M1 switch is pressed within 3 seconds after the SET switch is being pressed.
Move the seat out of the foremost and uppermost positions using the front power seat switch LH (w/ Memory).
Check that the buzzer sounds for 0.5 seconds and the seat position is memorized when the M2 switch is pressed within 3 seconds after the SET switch is being pressed.
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves into the foremost and uppermost positions (memorized positions) when the M1 switch is pressed.
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves out of the foremost and uppermost positions (memorized positions) when the M2 switch is pressed.
Turn the engine switch off and open the driver door. Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position by pressing the M1 or M2 switch within 180 seconds after the engine switch is turned off.
Turn the engine switch off and close the driver door. Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position by pressing the M1 or M2 switch within 60 seconds after the engine switch is turned off.
Operate the front vertical function of the power seat switch to tilt the seat down 3 times.
Within 10 seconds after operating the front vertical function of the power seat switch, operate the lifter function of the power seat switch to tilt up and the reclining function of the power seat switch to recline the seat simultaneously. Hold both switches for 10 seconds.
| CHECK MEMORY CALL FUNCTION |
Automatic memory call function check
With a transmitter key recognition code registered:
Perform a wireless door unlock or entry unlock operation and check that opening the driver door causes the following:
Memory registration
With the engine switch off and the driver door closed, press and hold the M1 or M2 switch while carrying the key. The main body ECU (multiplex network body ECU) will enter transmitter key recognition code registration mode to allow a key to be linked to the mirror surface memory position.
When the manual LOCK or UNLOCK switch on the multiplex network master switch assembly is pressed, check that the buzzer sounds for 0.5 seconds.
Memory deletion
With the engine switch off and the driver door closed, press and hold the SET switch while carrying the key. The main body ECU (multiplex network body ECU) will enter transmitter key recognition code deletion mode.
When the manual LOCK or UNLOCK switch on the multiplex network master switch assembly is pressed, check that the buzzer sounds twice (0.1 seconds each time).
| MEMORY CALL EMERGENCY STOP FUNCTION |
While a memory call function is operating, check that performing one of the following will stop the memory call operation: 1) press the SET switch, M1 switch or M2 switch or 2) press the power seat switch.