Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM

DTC    B2782    Power Source Control ECU Malfunction

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) has a power source mode switching function.
This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU is determined to be abnormal.

HINT:
The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No.
Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2782
Either condition is met (1-trip detection logic*):
  1. The steering lock motor activation command circuit has a short circuit.
  2. The steering lock motor activation command circuit has an open circuit.

HINT:
If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.

  1. Steering lock ECU (Steering lock actuator assembly)
  2. Certification ECU (Smart key ECU assembly)
  3. Harness or connector
Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P and the engine switch off. The steering unlocks when the engine switch is turned on (ACC) or on (IG) while carrying the key.)
  1. *: Only output while a malfunction is present and the engine switch is on (IG).

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started.
Prohibits the engine from being started (the engine does not crank).

Related Data List and Active Test Items 
DTC No.
Data List Item
Active Test Item
B2782
Entry&Start
  1. Power Supply Short
-

WIRING DIAGRAM


C277550E04


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.
  2. The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  3. When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).
  4. After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again (Click here).
  5. When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (refer to Service Bulletin).

1.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the I24 steering lock ECU connector.



    C157850E40
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I24-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Lock ECU (Steering Lock Actuator Assembly))

  1. Reconnect the I24 steering lock ECU connector.

  1. Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P.



    C241547E02
  1. Check the signal waveform according to the condition(s) in the table below.
    Standard Frequency 
    Item
    Content
    Tester Connection
    I24-3 (IGE) - I24-1 (GND)
    Tool Setting
    2 V/DIV., 200 ms./DIV.
    Vehicle Condition
    Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating
    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock ECU (Steering Lock Actuator Assembly))
    *b
    Steering lock motor not operating
    *c
    Steering lock motor operating

    HINT:
    1. When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
    2. In order to take measurements when the lock motor is operating, perform either of the following operations:
      1. To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.
      2. To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.



NG
Go to step 4
OK


2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD
  1. Clear the DTCs (Click here).

  1. Disconnect the cable from the negative (-) battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) battery terminal to clear the record of malfunctions stored in the Data List.

    CAUTION:
    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work (Click here).


NEXT


3.CHECK DTC
  1. Perform the DTC output confirmation operation.

  1. Check if DTC B2782 is output (Click here).


Result:

Result
Proceed to
DTC B2782 is not output.
A
DTC B2782 is output.
B



B
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (Click here)
A

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR) 

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the I24 steering lock ECU connector.

  1. Disconnect the I78 certification ECU (smart key ECU assembly) connector.

  1. Check for deformation and corrosion of the connector case and terminals.

    OK:
    There is no deformation or corrosion of the connector case or terminals.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I24-3 (IGE) - I78-29 (SLR+)
    Always
    Below 1 Ω
    I24-3 (IGE) - Body ground
    Always
    10 kΩ or higher
    I78-29 (SLR+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)