FRONT SEAT ASSEMBLY (for TMMK Made Manual Seat) > DISASSEMBLY |
| 1. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH |
![]() |
Disconnect the connector.
Disengage the clamp.
Remove the nut and front seat inner belt assembly RH.
| 2. REMOVE LOWER SEAT TRACK RAIL |
Remove the lower seat track rail.
| 3. REMOVE SEAT ADJUSTER COVER CAP |
![]() |
Remove the 2 seat adjuster cover caps.
| 4. REMOVE RECLINING ADJUSTER RELEASE HANDLE |
![]() |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.
| *a | Protective Tape |
| 5. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Disconnect the 2 rubber bands of the separate type front seatback cover.
| 6. REMOVE FRONT SEAT CUSHION SHIELD |
![]() |
Remove the 2 screws.
Disengage the 2 claws to remove the front seat cushion shield.
| 7. REMOVE FRONT SEAT INNER CUSHION SHIELD |
![]() |
Remove the 2 screws and front seat inner cushion shield.
| 8. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD |
![]() |
Disengage the claw and 3 clamps to separate the front seat airbag assembly wire harness.
![]() |
Separate the separate type front seat cushion cover.
![]() |
Disengage each hook and remove the separate type front seat cushion cover with pad.
| 9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Remove the 12 hog rings and the separate type front seat cushion cover from the separate type front seat cushion pad.
| 10. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD |
![]() |
Disengage the hook.
![]() |
Disengage the 2 fasteners.
![]() |
Turn back the separate type front seatback cover.
![]() |
Disengage the 2 hooks.
![]() |
Disengage the 4 claws and remove the 2 front seat headrest supports.
![]() |
Remove the separate type front seatback cover with pad.
| 11. REMOVE FRONT SEAT AIRBAG ASSEMBLY |
![]() |
Disengage the 2 clamps.
Remove the 2 nuts and the front seat airbag assembly.
| 12. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
Remove the 2 hog rings.
Disengage the 2 fasteners to remove the separate type front seatback cover from the separate type front seatback pad.
| 13. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH |
![]() |
Disengage the 2 claws to remove the front seat lower cushion shield LH.
| 14. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH |
| 15. REMOVE FRONT UPPER SEAT TRACK COVER LH |
![]() |
Disengage the 2 claws to remove the front upper seat track cover LH.
| 16. REMOVE FRONT UPPER SEAT TRACK COVER RH |
![]() |
Disengage the 2 claws to remove the front upper seat track cover RH.
| 17. REMOVE REAR UPPER SEAT TRACK COVER LH |
![]() |
Disengage the 2 claws to remove the rear upper seat track cover LH.
| 18. REMOVE REAR UPPER SEAT TRACK COVER RH |
![]() |
Disengage the 2 claws to remove the rear upper seat track cover RH.
| 19. REMOVE UPPER NO. 3 SEAT TRACK COVER |
![]() |
Disengage the 2 claws to remove the upper No. 3 seat track cover.
| 20. REMOVE UPPER NO. 4 SEAT TRACK COVER |
![]() |
Disengage the 2 claws to remove the upper No. 4 seat track cover.
| 21. REMOVE OCCUPANT DETECTION ECU |
![]() |
Disconnect the 2 connectors.
Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the occupant detection ECU.
| *1 | Protective Tape |
| 22. REMOVE FRONT SEAT WIRE |
Disconnect each connector and disengage each clamp to remove the front seat wire.
| 23. REMOVE RECLINING CONTROL LEVER |
![]() |
Remove the bolt and reclining control lever.
| 24. REMOVE FRONT SEATBACK FRAME SUB-ASSEMBLY |
![]() |
Remove the 4 bolts and the front seatback frame sub-assembly.
| 25. REMOVE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides to remove the separate type front seatback spring assembly.
Remove the 2 front seatback hooks from the separate type front seatback spring assembly.
| 26. REMOVE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY |
![]() |
Remove the separate type front seat cushion spring assembly.