Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

NAVIGATION SYSTEM (for Navigation Receiver Type) > Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter

for Preparation Click here


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the navigation receiver assembly via this circuit.
The sound signal that has been sent is amplified by the navigation receiver assembly and then is sent to the speakers.
If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.

WIRING DIAGRAM


E277819E49


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
  1. Disconnect the I67 navigation receiver assembly connector.

  1. Disconnect the I204 No. 1 stereo jack adapter assembly connector (for TMC Made).
    Disconnect the I146 No. 1 stereo jack adapter assembly connector (for TMMK Made).



    E277839E12
  1. Measure the resistance according to the value(s) in the table below (for TMC Made).

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-25 (ADPG) - I204-10 (AUXO)
    Always
    Below 1 Ω
    I67-26 (VAR+) - I204-7 (ARO)
    Always
    Below 1 Ω
    I67-28 (VAL+) - I204-8 (ALO)
    Always
    Below 1 Ω
    I67-27 (VA-) - I204-9 (ASGN)
    Always
    Below 1 Ω
    I67-11 (AGND) - I204-12 (AGND)
    Always
    Below 1 Ω
    I67-25 (ADPG) - Body ground
    Always
    10 kΩ or higher
    I67-26 (VAR+) - Body ground
    Always
    10 kΩ or higher
    I67-28 (VAL+) - Body ground
    Always
    10 kΩ or higher
    I67-27 (VA-) - Body ground
    Always
    10 kΩ or higher
    I67-11 (AGND) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E227392E74
  1. Measure the resistance according to the value(s) in the table below (for TMMK Made).

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-25 (ADPG) - I146-9 (AUXO)
    Always
    Below 1 Ω
    I67-26 (VAR+) - I146-6 (ARO)
    Always
    Below 1 Ω
    I67-28 (VAL+) - I146-7 (ALO)
    Always
    Below 1 Ω
    I67-27 (VA-) - I146-8 (ASGN)
    Always
    Below 1 Ω
    I67-11 (AGND) - I146-10 (AGND)
    Always
    Below 1 Ω
    I67-25 (ADPG) - Body ground
    Always
    10 kΩ or higher
    I67-26 (VAR+) - Body ground
    Always
    10 kΩ or higher
    I67-28 (VAL+) - Body ground
    Always
    10 kΩ or higher
    I67-27 (VA-) - Body ground
    Always
    10 kΩ or higher
    I67-11 (AGND) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)