AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Data Signal Circuit between Radio Receiver and Stereo Jack Adapter |
| for LHD (w/ Wireless Charger System) |

| for LHD (w/o Wireless Charger System) |

| for RHD |

| 1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY) |
Disconnect the I156 radio and display receiver assembly connector. (w/o Display Signal Line)
Disconnect the I205 radio and display receiver assembly connector. (w/ Display Signal Line)
Disconnect the I146 No. 1 stereo jack adapter assembly connector. (for RHD without Display Signal Line)
Disconnect the I204 No. 1 stereo jack adapter assembly connector. (for RHD with Display Signal Line), (for LHD without Wireless Charger System)
Disconnect the I207 No. 1 stereo jack adapter assembly connector. (for LHD with Wireless Charger System)
![]() |
Measure the resistance according to the value(s) in the table below. (for RHD with Display Signal Line), (for LHD without Wireless Charger System)
| Tester Connection | Condition | Specified Condition |
| I205-2 (UDO-) - I204-2 (UDO-) | Always | Below 1 Ω |
| I205-3 (UDO+) - I204-3 (UDO+) | Always | Below 1 Ω |
| I205-5 (USG1) - I204-5 (UJSS) | Always | Below 1 Ω |
| I205-2 (UDO-) - Body ground | Always | 10 kΩ or higher |
| I205-3 (UDO+) - Body ground | Always | 10 kΩ or higher |
| I205-5 (USG1) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector (to No. 1 Stereo Jack Adapter Assembly) |
![]() |
Measure the resistance according to the value(s) in the table below. (for LHD with Wireless Charger System)
| Tester Connection | Condition | Specified Condition |
| I205-2 (UDO-) - I207-2 (UDO-) | Always | Below 1 Ω |
| I205-3 (UDO+) - I207-3 (UDO+) | Always | Below 1 Ω |
| I205-5 (USG1) - I207-5 (UJSS) | Always | Below 1 Ω |
| I205-2 (UDO-) - Body ground | Always | 10 kΩ or higher |
| I205-3 (UDO+) - Body ground | Always | 10 kΩ or higher |
| I205-5 (USG1) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector (to No. 1 Stereo Jack Adapter Assembly) |
![]() |
Measure the resistance according to the value(s) in the table below. (for RHD without Display Signal Line)
| Tester Connection | Condition | Specified Condition |
| I156-2 (US1-) - I146-2 (UDO-) | Always | Below 1 Ω |
| I156-3 (US1+) - I146-3 (UDO+) | Always | Below 1 Ω |
| I156-5 (USG1) - I146-5 (UJSS) | Always | Below 1 Ω |
| I156-2 (US1-) - Body ground | Always | 10 kΩ or higher |
| I156-3 (US1+) - Body ground | Always | 10 kΩ or higher |
| I156-5 (USG1) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector (to No. 1 Stereo Jack Adapter Assembly) |
![]() |
Measure the resistance according to the value(s) in the table below. (for LHD without Wireless Charger System)
| Tester Connection | Condition | Specified Condition |
| I156-2 (UDO-) - I204-2 (UDO-) | Always | Below 1 Ω |
| I156-3 (UDO+) - I204-3 (UDO+) | Always | Below 1 Ω |
| I156-5 (USG1) - I204-5 (UJSS) | Always | Below 1 Ω |
| I156-2 (UDO-) - Body ground | Always | 10 kΩ or higher |
| I156-3 (UDO+) - Body ground | Always | 10 kΩ or higher |
| I156-5 (USG1) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector (to No. 1 Stereo Jack Adapter Assembly) |
|
| ||||
| OK | ||
| ||