Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for TMMK Made)

ROOF HEADLINING (for TMMK Made) > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing (Click here).

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT DOOR SCUFF PLATE LH


    B395175E01
  1. Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

  1. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

  1. Disengage the 6 claws (C) to remove the front door scuff plate LH.



4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B278978
  1. Remove the clip.

  1. Pull the cowl side trim sub-assembly LH as shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.



5. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the front door opening trim weatherstrip LH.



6. REMOVE FRONT PILLAR GARNISH LH


    B379543E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    HINT:
    Make the front pillar garnish LH hang from the front pillar garnish clip.



    B379544E02
  1. While pushing the tabs of the front pillar garnish clip in the direction indicated by the arrows (A) shown in the illustration, disengage the front pillar garnish clip.

    NOTICE:
    Do not apply excessive force using a tool.

  1. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

  1. Remove the 2 clips from the front pillar garnish LH.



    B278988E02
  1. Protect the curtain shield airbag assembly LH.
    Text in Illustration 
    *1
    Curtain Shield Airbag Assembly LH
    *a
    Protective Cover
    V100155
    Adhesive Tape

    1. Cover the curtain shield airbag assembly LH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.



7. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



10. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



11. REMOVE REAR SEAT CUSHION ASSEMBLY


    B279202E01
  1. Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



12. REMOVE REAR SEAT CUSHION LOCK HOOK


    B393387
  1. Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the RH side and the LH side.



13. REMOVE INNER LUGGAGE COMPARTMENT TRIM PAD


    B279201
  1. Remove the inner luggage compartment trim pad.



14. REMOVE REAR SEATBACK ASSEMBLY LH


    B279209E02
  1. Disengage the 2 fasteners as shown in the illustration.
    Text in Illustration 
    *a
    Fastener



    B279211
  1. Remove the 2 bolts and rear seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



15. REMOVE REAR SEATBACK ASSEMBLY RH


    B279206E02
  1. Disengage the 3 fasteners as shown in the illustration.
    Text in Illustration 
    *a
    Fastener



    B279208
  1. Remove the 2 bolts and rear seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



16. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
  1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide.

  1. Disconnect the connector.



    B285010
  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear side seatback assembly LH.



17. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
  1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide.

  1. Disconnect the connector.



    B285009
  1. Remove the 2 bolts.

  1. Disengage the hook and remove the rear side seatback assembly RH.



18. REMOVE REAR DOOR SCUFF PLATE LH


    B395176E01
  1. Disengage the claw (A) in the direction indicated by the arrow (1) shown in the illustration.

  1. Disengage the claw (B) in the direction indicated by the arrow (2) shown in the illustration.

  1. Disengage the 4 claws (C) to remove the rear door scuff plate LH.

    HINT:
    Disengage the claws from the front side of the rear door scuff plate LH.



19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the rear door opening trim weatherstrip LH.



20. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    B271081
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



21. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B271083
  1. Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.



    B271084E02
  1. Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B271085
  1. Remove the 2 bolts and front seat outer belt assembly.



22. REMOVE CENTER PILLAR LOWER GARNISH LH


    B278989
  1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.



23. REMOVE CENTER PILLAR UPPER GARNISH LH


    B278990
  1. Remove the 2 screws.

  1. Disengage the clip.

  1. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.

  1. Remove the clip from the center pillar upper garnish LH.



24. REMOVE ROOF SIDE INNER GARNISH LH


    B387550
  1. Disengage the 5 clips.

  1. Disengage the guide and remove the roof side inner garnish LH.

  1. Remove the 5 clips from the roof side inner garnish LH.



25. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



26. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



27. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



28. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



29. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side.



30. REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:
Use the same procedure as for the LH side.



31. REMOVE ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure as for the LH side.



32. REMOVE FRONT SEAT ASSEMBLY LH
(Click here)


33. REMOVE FRONT SEAT ASSEMBLY RH
for Manual Seat: (Click here)
for Power Seat:

HINT:
Use the same procedure as for the LH side.



34. REMOVE INSTRUMENT PANEL ASSEMBLY
(Click here)


35. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


  1. except TMMR Made:



      B281435
    1. Disengage the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow shown in the illustration.



    2. B281437
    3. Disengage the 6 claws and remove the inner rear view mirror stay holder cover.



  1. for TMMR Made:



      B380967
    1. Disengage the 2 guides and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow shown in the illustration.



    B380969
  1. Disengage the 2 claws and remove the inner rear view mirror stay holder cover.



36. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)


    E226707
  1. Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the roof console box assembly.



37. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)


    E226709
  1. Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the roof console box assembly.



38. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)


    E228309E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.
    Text in Illustration 
    *1
    Protective Tape
    *a
    Front



    E228310E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws as shown in the illustration and remove the No. 1 room light housing.
    Text in Illustration 
    *1
    Protective Tape
    *a
    Front



    E220648E02
  1. Using a screwdriver, disengage the 4 claws and disconnect the room light switch base from the No. 1 room light housing.
    Text in Illustration 
    *1
    Room Light Switch Base



39. REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)


    E227560E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 8 claws and remove the 2 spot light lenses.
    Text in Illustration 
    *1
    Protective Tape
    *a
    Front



    E227562E01
  1. Using a screwdriver with its tip wrapped with protective tape and moulding remover, disengage the 2 claws <A>.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Claw <A>
    *3
    Claw <B>
    *4
    Claw <C>
    *a
    Front

  1. Disengage the 2 claws <B> and 2 claws <C>, and disconnect the spot light housing.



    E227564E01
  1. Using a screwdriver, disengage the 8 claws and disconnect the 2 map light sub-assemblies from the spot light housing.
    Text in Illustration 
    *1
    Map Light Sub-assembly



40. REMOVE ASSIST GRIP SUB-ASSEMBLY


    B278995E02
  1. Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    Tape the screwdriver tip before use.



    B278999
  1. Disengage the 2 clips and remove the assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side.



41. REMOVE REAR ASSIST GRIP ASSEMBLY LH


    B278997E02
  1. Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    Tape the screwdriver tip before use.



    B279000
  1. Disengage the 2 clips and remove the rear assist grip assembly LH.

  1. Remove the 2 clips from the vehicle body.



42. REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



43. REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
  1. Remove the sliding roof opening trim moulding.



44. REMOVE VISOR BRACKET COVER (for LH Side)


    B278992
  1. Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.



45. REMOVE VISOR ASSEMBLY LH


    B278994
  1. Remove the 2 screws and visor assembly LH.



46. REMOVE VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



47. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



48. REMOVE VISOR HOLDER


    B211697E01
  1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    HINT:
    Use the same procedure for the other visor holder.



49. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
  1. w/ EC Mirror:

    1. Disconnect the connector from the inner rear view mirror.



  1. Remove the bolt and disconnect the bracket from the front pillar RH.


    B396425

  1. Disengage the 3 clamps from the front pillar RH.

  1. Disengage the 4 clamps from the front pillar LH.

  1. Disengage the 2 clamps and disconnect the connector from the rear pillar RH.

  1. Remove the 2 clips.

  1. Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

    HINT:
    Leave the 2 clips in the vehicle.



    B279009
  1. Remove the roof headlining assembly from the vehicle through the front door RH.

    NOTICE:
    Do not damage the roof headlining assembly or vehicle interior.



    B279104
  1. Remove the 2 clips from the vehicle body as shown in the illustration.



50. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
  1. w/ EC Mirror:

    1. Disconnect the connector from the inner rear view mirror.



  1. Disconnect the connector from the sliding roof drive gear assembly.


    B396426

  1. Remove the bolt and disconnect the bracket from the front pillar RH.

  1. Disengage the 3 clamps from the front pillar RH.

  1. Disengage the 4 clamps from the front pillar LH.

  1. Disengage the 2 clamps and disconnect the connector from the rear pillar RH.

  1. Remove the 2 clips.

  1. Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

    HINT:
    Leave the 2 clips in the vehicle.



    B279010
  1. Remove the roof headlining assembly from the vehicle through the front door RH.

    NOTICE:
    Do not damage the roof headlining assembly or vehicle interior.



    B279104
  1. Remove the 2 clips from the vehicle body as shown in the illustration.