REAR POWER OUTLET SOCKET > REMOVAL |
| 1. PRECAUTION (w/ Rear Seat Side Airbag) |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag) |
| 3. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 4. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY |
| 5. REMOVE REAR SEAT CUSHION ASSEMBLY |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
Disconnect the 2 seat heater connectors.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 6. REMOVE REAR SEAT CUSHION LOCK HOOK |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 7. REMOVE REAR SEATBACK COVER |
![]() |
Disengage the 4 claws and remove the 2 rear seatback covers.
| 8. REMOVE REAR SEATBACK ASSEMBLY LH |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.
Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly LH.
| 9. REMOVE REAR SEATBACK ASSEMBLY RH |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly RH.
Disengage the rear seat belt from the rear seat shoulder belt guide.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly RH.
| 10. REMOVE CENTER SEATBACK ASSEMBLY |
Disconnect the connector.
![]() |
Remove the 2 bolts.
Disengage the hook and remove the center seatback assembly as shown in the illustration.
| 11. REMOVE CENTER SEAT ARMREST INNER PLATE |
![]() |
Disengage the 6 claws and separate the 4 guides, and remove the center seat armrest inner plate.
| 12. REMOVE REAR CENTER SEATBACK FRAME WITH COVER AND PAD |
![]() |
Remove the 2 nuts.
Disengage the 2 claws and remove the rear center seatback frame with cover and pad.
| 13. REMOVE CENTER SEAT ARMREST BRACKET SUB-ASSEMBLY |
![]() |
Disengage the 3 clamps.
Remove the 2 bolts, 2 washers and center seat armrest bracket sub-assembly.
| 14. REMOVE REAR SEAT CENTER ARMREST BOX ASSEMBLY |
![]() |
Disengage the 4 hooks and remove the rear seat center armrest box assembly from the rear seat center armrest.
| 15. REMOVE COOLER CONTROL SWITCH ASSEMBLY |
![]() |
Remove the 2 screws.
Separate the guide and remove the rear seat center armrest door sub-assembly.
![]() |
Remove the screw.
Using a moulding remover, disengage the 8 claws and 3 guides, and remove the rear seat armrest plate.
![]() |
Disengage the 4 claws.
![]() |
Disconnect each connector to remove the cooler control switch assembly.
| 16. REMOVE REAR NO. 1 POWER OUTLET SOCKET ASSEMBLY |
![]() |
Disengage the guide.
![]() |
Disengage the 3 clamps and turn back the rear seat center armrest cover as shown in the illustration.
![]() |
Disconnect the connector.
![]() |
Using a screwdriver, disengage the claw and remove the rear No. 1 power outlet socket assembly as shown in the illustration.
| *1 | Protective Tape |
| 17. REMOVE REAR POWER OUTLET SOCKET COVER |
![]() |
Disengage the 2 claws and remove the rear power outlet socket cover as shown in the illustration.