REAR SEAT ASSEMBLY (for TMC, TMMR Made Fold Down Seat Type) > REASSEMBLY |
| 1. INSTALL BENCH TYPE REAR SEAT CUSHION COVER |
Temporarily install the bench type rear seat cushion cover to the bench type rear seat cushion pad.
Using hog ring pliers, install 24 new hog rings.

w/o Seat Heater System:
Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 46 new hog rings.

w/ Seat Heater System:
Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 48 new hog rings.

| 2. INSTALL SEPARATE TYPE REAR SEATBACK COVER (for LH Side) |
![]() |
Using hog ring pliers, install the separate type rear seatback cover with 6 new hog rings.
| 3. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side) |
Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.
![]() |
Engage the 4 claws to install the 2 rear seat headrest supports.
![]() |
Engage the 2 hooks.
![]() |
Using hog ring pliers, install 6 new hog rings.
![]() |
Engage the 2 hooks to install the separate type rear seatback cover with pad.
| 4. INSTALL REAR SEATBACK UPPER LOCK BEZEL (for LH Side) |
![]() |
Engage the 4 claws to install the rear seatback upper lock bezel.
| 5. INSTALL REAR SEAT CENTER SHOULDER BELT GUIDE (for LH Side) |
![]() |
Engage the guide.
Install the rear seat center shoulder belt guide with the 2 screws.
| 6. INSTALL SEPARATE TYPE REAR SEATBACK COVER (for RH Side) |
![]() |
Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 8 new hog rings.
![]() |
Using hog ring pliers, install 7 new hog rings.
| 7. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side) |
Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly RH.
![]() |
Engage the 4 claws to install the 2 front seat headrest supports.
![]() |
Engage the 2 hooks.
![]() |
Using hog ring pliers, install the rear separate type seatback cover with pad to the seatback frame with 7 new hog rings.
![]() |
Engage the 2 hooks to install the separate type rear seatback cover with pad.
| 8. INSTALL REAR SEATBACK UPPER LOCK BEZEL (for RH Side) |
![]() |
Engage the 4 claws to install the rear seatback upper lock bezel.
| 9. INSTALL REAR SEATBACK HINGE COVER (for RH Side) |
![]() |
Install the rear seatback hinge cover as shown in the illustration.
| 10. INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY (for RH Side) |
![]() |
Engage the 2 claws and 2 guides as indicated by the arrows, in the order shown in the illustration to install the rear seat center armrest cup holder sub-assembly.
| 11. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (for RH Side) |
![]() |
Engage the 2 claws to install the bush.
![]() |
Engage the guide.
Install the rear seat center armrest assembly with the bolt and washer.
| 12. INSTALL NO. 1 SEAT ARMREST CAP (for RH Side) |
![]() |
Engage the 3 claws to install the No. 1 seat armrest cap.
| 13. INSTALL REAR SEAT SHOULDER BELT GUIDE LH |
![]() |
Engage the guide.
Install the rear seat shoulder belt guide LH with the 2 screws.
| 14. INSTALL REAR SEAT SHOULDER BELT GUIDE RH |
![]() |
Engage the guide.
Install the rear seat shoulder belt guide RH with the 2 screws.