REAR SEATBACK HEATER (for Fold Down Seat Type) > INSTALLATION |
| 1. INSTALL SEPARATE TYPE REAR SEATBACK COVER (REAR SEATBACK HEATER SUB-ASSEMBLY) (for LH Side) |
![]() |
Using hog ring pliers, install the separate type rear seatback cover (rear seatback heater sub-assembly) with 6 new hog rings.
| 2. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side) |
Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.
![]() |
Engage the 4 claws to install the 2 rear seat headrest supports.
![]() |
Engage the 2 hooks.
![]() |
Using hog ring pliers, install 6 new hog rings.
![]() |
Engage the 2 hooks to install the separate type rear seatback cover with pad.
| 3. INSTALL REAR SEATBACK UPPER LOCK BEZEL (for LH Side) |
![]() |
Engage the 4 claws to install the rear seatback upper lock bezel.
| 4. INSTALL REAR SEAT CENTER SHOULDER BELT GUIDE (for LH Side) |
![]() |
Engage the guide.
Install the rear seat center shoulder belt guide with the 2 screws.
| 5. INSTALL SEPARATE TYPE REAR SEATBACK COVER (REAR SEATBACK HEATER SUB-ASSEMBLY) (for RH Side) |
![]() |
Using hog ring pliers, install the separate type rear seatback cover (rear seatback heater sub-assembly) to the separate type rear seatback pad with 8 new hog rings.
![]() |
Using hog ring pliers, install 7 new hog rings.
| 6. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side) |
Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly RH.
![]() |
Engage the 4 claws to install the 2 front seat headrest supports.
![]() |
Engage the 2 hooks.
![]() |
Using hog ring pliers, install the rear separate type seatback cover with pad to the seatback frame with 7 new hog rings.
![]() |
Engage the 2 hooks to install the separate type rear seatback cover with pad.
| 7. INSTALL REAR SEATBACK UPPER LOCK BEZEL (for RH Side) |
![]() |
Engage the 4 claws to install the rear seatback upper lock bezel.
| 8. INSTALL REAR SEATBACK HINGE COVER (for RH Side) |
![]() |
Install the rear seatback hinge cover as shown in the illustration.
| 9. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (for RH Side) |
![]() |
Engage the 2 claws to install the bush.
![]() |
Engage the guide.
Install the rear seat center armrest assembly with the bolt and washer.
| 10. INSTALL NO. 1 SEAT ARMREST CAP (for RH Side) |
![]() |
Engage the 3 claws to install the No. 1 seat armrest cap.
| 11. INSTALL REAR SEATBACK ASSEMBLY LH |
Place the rear seatback assembly LH in the cabin.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
Install the rear seatback assembly LH with the 2 bolts.
![]() |
Engage the fastener as shown in the illustration.
Raise the rear seatback assembly LH.
Connect the rear seat outer belt assembly to the rear seat center shoulder belt guide.
| 12. INSTALL REAR SEATBACK ASSEMBLY RH |
Place the rear seatback assembly RH in the cabin.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
Install the rear seatback assembly RH with the 2 bolts.
![]() |
Engage the fastener as shown in the illustration.
Raise the rear seatback assembly RH.
| 13. INSTALL REAR SEAT HEADREST ASSEMBLY |