AIR CONDITIONING SYSTEM > TERMINALS OF ECU |
| AIR CONDITIONING AMPLIFIER ASSEMBLY |

| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I77-1 (IG+) - I77-14 (GND) | B - W-B | Power source (IG) | Ignition switch ON | 11 to 14 V |
| I77-1 (IG+) - I77-14 (GND) | B - W-B | Power source (IG) | Ignition switch off | Below 1 V |
| I77-2 (SOL+) - I77-14 (GND) | W - W-B*3 GR - W-B*4 | Compressor solenoid operation signal | Engine running A/C switch: on Blower switch: LO | Pulse generation (See waveform 1) |
| I77-5 (TAM) - I77-13 (SG-2) | P - GR | Ambient temperature sensor signal | Ignition switch ON Ambient temperature: 25°C (77°F) | 1.35 to 1.75 V |
| I77-5 (TAM) - I77-13 (SG-2) | P - GR | Ambient temperature sensor signal | Ignition switch ON Ambient temperature: 40°C (104°F) | 0.9 to 1.2 V |
| I77-7 (FLOQ) - I77-13 (SG-2) | G - GR*3 LG - GR*4 | A/C flow sensor signal | Ignition switch ON A/C switch: off | 3.8 to 4.2 V |
| I77-7 (FLOQ) - I77-13 (SG-2) | G - GR*3 LG - GR*4 | A/C flow sensor signal | Ignition switch ON A/C switch: on Blower switch: HI | 0.7 to 3.8 V |
| I77-8 (LOCK) - I77-13 (SG-2)*1 | SB - GR | A/C lock sensor signal | Engine running Blower switch: LO A/C switch: on | Pulse generation (See waveform 2) |
| I77-9 (PRE) - I77-13 (SG-2) | R - GR | Air conditioning pressure sensor signal | Engine running A/C system operating Refrigerant pressure: Abnormal pressure (more than 3025 kPa (30.9 kgf/cm2, 439 psi)) | 4.80 V or higher |
| I77-9 (PRE) - I77-13 (SG-2) | R - GR | Air conditioning pressure sensor signal | Engine running A/C system operating Refrigerant pressure: Abnormal pressure (less than 176 kPa (1.8 kgf/cm2, 25 psi)) | Below 0.50 V |
| I77-9 (PRE) - I77-13 (SG-2) | R - GR | Air conditioning pressure sensor signal | Engine running A/C system operating Refrigerant pressure: Normal pressure (less than 3025 kPa (30.9 kgf/cm2, 439 psi) and more than 176 kPa (1.8 kgf/cm2, 25 psi)) | 0.50 to 4.80 V |
| I77-10 (S5-3) - I77-13 (SG-2) | V - GR | Power supply for air conditioning pressure sensor | Ignition switch ON A/C switch: on | 4.75 to 5.25 V |
| I77-10 (S5-3) - I77-13 (SG-2) | V - GR | Power supply for air conditioning pressure sensor | Ignition switch ON A/C switch: off | Below 1 V |
| I77-11 (CANH) - I77-12 (CANL) | V - W | CAN communication system | CAN communication occurring | Pulse generation |
| I77-13 (SG-2) - Body ground | GR - Body ground | Ground for air conditioning pressure sensor, ambient temperature sensor, A/C lock sensor | Always | Below 1 V |
| I77-14 (GND) - Body ground | W-B - Body ground | Ground for main power supply | Always | Below 1 V |
| I77-15 (PTC1) - I77-14 (GND)*5 | G - W-B | Quick heater assembly operation signal | Engine running Temperature settings: MAX HOT Ambient temperature: 10°C (50°F) or lower Engine coolant temperature: 75°C (167°F) or lower Light control switch off Blower switch: On | Below 1 V |
| I77-15 (PTC1) - I77-14 (GND)*5 | G - W-B | Quick heater assembly operation signal | Engine running Temperature settings: MAX HOT Ambient temperature: 10°C (50°F) or lower Engine coolant temperature: 75°C (167°F) or lower Light control switch off Blower switch: Off | 11 to 14 V |
| I77-16 (PTC2) - I77-14 (GND)*5 | L - W-B | Quick heater assembly operation signal | Engine running Temperature settings: MAX HOT Ambient temperature: 10°C (50°F) or lower Engine coolant temperature: 70°C (158°F) or lower Light control switch off Blower switch: On | Below 1 V |
| I77-16 (PTC2) - I77-14 (GND)*5 | L - W-B | Quick heater assembly operation signal | Engine running Temperature settings: MAX HOT Ambient temperature: 10°C (50°F) or lower Engine coolant temperature: 70°C (158°F) or lower Light control switch off Blower switch: Off | 11 to 14 V |
| I77-20 (MGC) - I77-14 (GND)*1 | B - W-B | Magnetic clutch operation signal | Engine running Blower switch: LO A/C switch: off | 11 to 14 V |
| I77-20 (MGC) - I77-14 (GND)*1 | B - W-B | Magnetic clutch operation signal | Engine running Blower switch: LO A/C switch: on | Below 1 V |
| I77-21 (B) - I77-14 (GND) | Y - W-B | Power source (Back-up) | Always | 11 to 14 V |
| I77-22 (BLW) - I77-14 (GND) | R - W-B | Blower motor speed control signal | Ignition switch ON Blower switch: LO | Pulse generation (See waveform 3) |
| I77-26 (NAIN) - I77-14 (GND)*2 | Y - W-B | Ion generator sub-assembly operation condition signal | Ignition switch ON Blower switch: LO | Below 1 V |
| I77-26 (NAIN) - I77-14 (GND)*2 | Y - W-B | Ion generator sub-assembly operation condition signal | Ignition switch ON Blower switch: OFF | 4.5 to 5.5 V |
| I77-29 (TR) - I77-34 (SG-1) | P - LG | Room temperature sensor signal | Ignition switch ON Cabin temperature: 25°C (77°F) | 1.8 to 2.2 V |
| I77-29 (TR) - I77-34 (SG-1) | P - LG | Room temperature sensor signal | Ignition switch ON Cabin temperature: 40°C (104°F) | 1.2 to 1.6 V |
| I77-30 (S5-1) - I77-14 (GND) | B - W-B | Power supply for A/C flow sensor | Ignition switch off | Below 1 V |
| I77-30 (S5-1) - I77-14 (GND) | B - W-B | Power supply for A/C flow sensor | Ignition switch ON | 4.5 to 5.5 V |
| I77-32 (TSP) - I77-14 (GND) | Y - W-B*3 R - W-B*4 | Solar sensor signal (for Front passenger side) | Ignition switch ON Solar sensor subjected to electric light | 0.8 to 4.3 V |
| I77-32 (TSP) - I77-14 (GND) | Y - W-B*3 R - W-B*4 | Solar sensor signal (for Front passenger side) | Ignition switch ON Solar sensor covered with a cloth | Below 0.8 V |
| I77-33 (TSD) - I77-14 (GND) | R - W-B*3 Y - W-B*4 | Solar sensor signal (for Driver side) | Ignition switch ON Solar sensor subjected to electric light | 0.8 to 4.3 V |
| I77-33 (TSD) - I77-14 (GND) | R - W-B*3 Y - W-B*4 | Solar sensor signal (for Driver side) | Ignition switch ON Solar sensor covered with a cloth | Below 0.8 V |
| I77-34 (SG-1) - Body ground | LG - Body ground | Ground for room temperature sensor | Always | Below 1 V |
| I77-37 (LIN1) - I77-14 (GND) | V - W-B | LIN communication signal | Ignition switch ON | Pulse generation |
| I77-39 (NANO) - I77-14 (GND)*2 | R - W-B | Ion generator operation signal | Ignition switch ON Blower switch: LO | 11 to 14 V |
| I77-39 (NANO) - I77-14 (GND)*2 | R - W-B | Ion generator operation signal | Ignition switch ON Blower switch: OFF | Below 1 V |
| z1-2 (BUS G) - Body ground | - | Ground for BUS IC | Always | Below 1 V |
| z1-3 (BUS) - z1-2 (BUS G) | - | BUS IC control signal | Ignition switch ON | Pulse generation |
| z1-4 (B BUS) - z1-2 (BUS G) | - | Power supply for BUS IC | Always | 11 to 14 V |
| z1-5 (SGA) - Body ground | - | Ground for evaporator temperature sensor | Always | Below 1 V |
| z1-6 (TEA) - z1-5 (SGA) | - | Evaporator temperature sensor signal | Ignition switch ON Evaporator temperature: 0°C (32°F) | 1.7 to 2.1 V |
| z1-6 (TEA) - z1-5 (SGA) | - | Evaporator temperature sensor signal | Ignition switch ON Evaporator temperature: 15°C (59°F) | 0.9 to 1.3 V |
![]() |
Waveform 1:
| Item | Content |
| Terminal No. | I77-2 (SOL+) - I77-14 (GND) |
| Tool Setting | 5 V/DIV., 500 μs./DIV. |
| Vehicle Condition | Engine running A/C switch: on Blower switch: LO |
![]() |
Waveform 2:
| Item | Content |
| Terminal No. | I77-8 (LOCK) - I77-13 (SG-2) |
| Tool Setting | 200 mV/DIV., 10 ms./DIV. |
| Vehicle Condition | Engine running Blower switch: LO A/C switch: on |
![]() |
Waveform 3:
| Item | Content |
| Terminal No. | I77-22 (BLW) - I77-14 (GND) |
| Tool Setting | 1 V/DIV., 500 μs./DIV. |
| Vehicle Condition | Ignition switch ON Blower switch: LO |
| AIR CONDITIONING PANEL (HEATER CONTROL SWITCH BOARD) (for TMC, TMMR Made) |

| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I56-2 (IG+) - I56-6 (GND) | R - W-B | Power source (IG) | Ignition switch off | Below 1 V |
| I56-2 (IG+) - I56-6 (GND) | R - W-B | Power source (IG) | Ignition switch ON | 11 to 14 V |
| I56-6 (GND) - Body ground | W-B - Body ground | Ground for air conditioning panel (heater control switch board) | Always | Below 1 V |
| I56-9 (LIN1) - Body ground | V - Body ground | LIN communication signal | Ignition switch ON | Pulse generation |
| I56-11 (ILL+) - I56-15 (ILL-) | G - W-B | Light control switch signal | Light control switch off | Below 1 V |
| I56-11 (ILL+) - I56-15 (ILL-) | G - W-B | Light control switch signal | Light control switch in tail or head position | 11 to 14 V |
| I56-15 (ILL-) - Body ground | W-B - Body ground | Ground for air conditioning panel (heater control switch board) illumination | Always | Below 1 V |
| AIR CONDITIONING CONTROL ASSEMBLY (for TMMK Made) |

| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I56-2 (IG+) - I56-6 (GND) | R - W-B | Power source (IG) | Ignition switch off | Below 1 V |
| I56-2 (IG+) - I56-6 (GND) | R - W-B | Power source (IG) | Ignition switch ON | 11 to 14 V |
| I56-6 (GND) - Body ground | W-B - Body ground | Ground for air conditioning control assembly | Always | Below 1 V |
| I56-9 (LIN1) - Body ground | V - Body ground | LIN communication signal | Ignition switch ON | Pulse generation |
| I56-11 (ILL+) - Body ground | G - Body ground | Illumination signal | Light control switch off | Below 1 V |
| I56-11 (ILL+) - Body ground | G - Body ground | Illumination signal | Light control switch in tail or head position | 11 to 14 V |
| I56-15 (ILL-) - Body ground | SB - Body ground | Illumination signal | Light control switch off | Below 1 V |
| I56-15 (ILL-) - Body ground | SB - Body ground | Illumination signal | Light control switch in tail or head position | Pulse generation |
| COOLER CONTROL SWITCH ASSEMBLY (for 3 Zone Type) |

| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| X1-1 (+B) - X1-16 (GND) | R - W-B | Power source (Back-up) | Always | 11 to 14 V |
| X1-6 (ACC) - X1-16 (GND) | GR - W-B | Power source (ACC) | Ignition switch off | Below 1 V |
| X1-6 (ACC) - X1-16 (GND) | GR - W-B | Power source (ACC) | Ignition switch ACC | 11 to 14 V |
| X1-7 (IG+) - X1-16 (GND) | V - W-B | Power source (IG) | Ignition switch off | Below 1 V |
| X1-7 (IG+) - X1-16 (GND) | V - W-B | Power source (IG) | Ignition switch ON | 11 to 14 V |
| X1-8 (ILL+) - X1-16 (GND) | G - W-B | Light control switch signal | Light control switch off | Below 1 V |
| X1-8 (ILL+) - X1-16 (GND) | G - W-B | Light control switch signal | Light control switch in tail or head position | 11 to 14 V |
| X1-10 (RLIN) - Body ground | B - Body ground | LIN communication signal | Ignition switch ON | Pulse generation |
| X1-16 (GND) - Body ground | W-B - Body ground | Ground for cooler control switch assembly | Always | Below 1 V |