Home › Drivetrain · U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0793    Intermediate Shaft Speed Sensor "A"

DTC    P07C5    Intermediate Shaft Speed Sensor "A" Circuit Low

DTC    P07C6    Intermediate Shaft Speed Sensor "A" Circuit High

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the counter gear which shows the output speed of transaxle. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (NC), the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

C133216E04


Text in Illustration 
*1
Counter Gear
*2
Clutch Drum
*3
Output Speed Sensor NC
*4
Input Speed Sensor NT

DTC No.
DTC Detection Condition
Trouble Area
P0793
When the vehicle speed is 25 km/h (15.5 mph) or higher, the counter gear speed is less than 300 rpm for 2 seconds or more. (1-trip detection logic)
  1. Transmission revolution sensor (speed sensor NC)
  2. Transmission wire
  3. TCM
P07C5
When the speed sensor input voltage is less than 0.1 V for 2 seconds or more. (1-trip detection logic)
P07C6
When the speed sensor input voltage is more than 1.9 V for 2 seconds or more. (1-trip detection logic)

MONITOR DESCRIPTION

The NT terminal of the TCM detects a revolution signal from the speed sensor (NT) (input RPM). The TCM calculates a gear shifts by comparing the speed sensor (NT) with the speed sensor (NC).
While the vehicle is operating in 2nd, 3rd, 4th or 5th gear with the shift lever in D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is more than 1000 rpm*2, the TCM interprets this as a fault, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM


C133260E26


INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the intelligent tester, read the Data List.

    Item
    Measurement Item/Range (display)
    Normal Condition
    Diagnostic Note
    SPD (NC)
    Counter Gear Speed/ display: 50 r/min
    -
    Data is displayed in increments of 50 rpm

    HINT:
    1. SPD (NC) is always 0 while driving: Open or short in the sensor or circuit.
    2. SPD (NC) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)
  1. Remove the valve body assembly.



    C133219
  1. Make sure that the connector is properly connected, and check the speed sensor installation (Click here).

    OK:
    The installation bolts are tightened properly and there is no clearance between the sensor and transaxle case.



NG
REPAIR OR REPLACE TRANSMISSION REVOLUTION SENSOR (Click here)
OK


2.INSPECT TRANSMISSION WIRE


    C189545E13
  1. Remove the TCM.

  1. Disconnect the speed sensor connector from the transmission wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    3 (NCO) sensor side - 3 (NCO) TCM side
    Always
    Below 1 Ω
    4 (NCB) sensor side - 4 (NCB) TCM side
    Always
    Below 1 Ω
    3 (NCO) sensor side - Body ground and other terminals
    Always
    10 kΩ or higher
    4 (NCB) sensor side - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)
    *b
    TCM side
    *c
    Sensor Side



NG
REPLACE TRANSMISSION WIRE (Click here)
OK


3.REPLACE TRANSMISSION REVOLUTION SENSOR
(Click here)

NEXT


4.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0793, P07C5 AND/OR P07C6 IS OUTPUT AGAIN)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester on.

  1. Clear the DTCs (Click here).

    HINT:
    Write down the currently output DTCs before clearing them.

  1. Perform the monitor drive pattern (Click here).

  1. Enter the following menus: Powertrain / ECT / DTC.

  1. Read the DTCs using the intelligent tester.

    Result:

    Display (DTC Output)
    Proceed to
    Only "P0793, P07C5 or P07C6" is output
    A
    No output
    B



B
END
A

REPLACE TCM (Click here)