Home › Drivetrain · U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0989    Transmission Fluid Pressure Sensor / Switch "E" Circuit Low

DTC    P0990    Transmission Fluid Pressure Sensor / Switch "E" Circuit High

for Preparation Click here


DESCRIPTION

ATF pressure switch No. 3 is installed in the lock-up solenoid ATF output passage and is used to detect a malfunction in the lock-up solenoid.

DTC No.
DTC Detection Condition
Trouble Area
P0989
Transmission fluid pressure switch No. 3 is OFF when lock-up occurs in response to a lock-up request (2 trip detection logic).
  1. ATF temperature sensor assembly (ATF pressure switch No. 3)
  2. Transmission wire
  3. TCM
P0990
When both of the following are detected (2 trip detection logic):
  1. Transmission fluid pressure switch No. 3 is ON when lock-up does not occur.
  2. Lock-up does not occur when shift solenoid valve (SLU) is requested to turn off in the lock-up range.

MONITOR DESCRIPTION

The TCM illuminates the MIL and stores the DTC when the TCM detects that the ATF pressure switch is OFF with the lock-up solenoid ON or when the TCM detects that the ATF pressure switch is ON with the lock-up solenoid OFF.

WIRING DIAGRAM


C133258E28


INSPECTION PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0989 OR P0990)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / DTC.

  1. Read the DTCs using the intelligent tester.

    Result:

    Display (DTC Output)
    Proceed to
    Only "P0990" is output
    A
    Only "P0989" is output
    B
    "P0989 or P0990" and other DTCs are output
    C

    HINT:
    If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.



B
Go to step 4

C
GO TO DTC CHART (Click here)
A


2.CHECK TRANSMISSION WIRE (SHORT TO GROUND)


    C133212E48
  1. Remove the TCM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    19 (TPS3) - Body ground (Valve body assembly) and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK

REPLACE TCM (Click here)  

3.CHECK ATF TEMPERATURE SENSOR ASSEMBLY (ATF PRESSURE SWITCH NO. 3)
  1. Remove the oil strainer assembly.



    C142709E01
  1. Disconnect the connector from the ATF temperature sensor assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    1 (TPS3) - Body ground (Valve body assembly) and other terminals
    Always
    10 kΩ or higher



NG
REPLACE ATF TEMPERATURE SENSOR ASSEMBLY (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)  

4.CHECK TRANSMISSION WIRE
  1. Remove the oil strainer assembly.



    C175651E16
  1. Remove the TCM.

  1. Disconnect the connector from the ATF temperature sensor assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    19 (TPS3) TCM side - 1 (TPS3) sensor side
    Always
    Below 1 Ω
    1 (TPS3) sensor side - Body ground (Valve body assembly) and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)
    *b
    TCM Side
    *c
    ATF Temperature Sensor Side



NG
REPLACE TRANSMISSION WIRE (Click here)
OK


5.REPLACE ATF TEMPERATURE SENSOR ASSEMBLY
(Click here)

NEXT


6.CHECK IF DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the intelligent tester on.

  1. Clear the DTCs (Click here).

    HINT:
    Write down the currently output DTCs before clearing them.

  1. Perform the monitor drive pattern (Click here).

  1. Enter the following menus: Powertrain / ECT / DTC.

  1. Read the DTCs using the intelligent tester.

    Result:

    Display (DTC Output)
    Proceed to
    Only "P0989" is output
    A
    No output
    B



B
END
A

REPLACE TCM (Click here)