Home › Drivetrain ยท U761E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL PUMP

OIL PUMP > INSPECTION

for Preparation Click here



1. INSPECT FRONT OIL PUMP ASSEMBLY


    C138512
  1. Turn the front oil pump drive gear with 2 screwdrivers and check that it rotates smoothly.

    NOTICE:
    Be careful not to damage the front oil pump oil seal lip.



2. INSPECT CLEARANCE OF FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY


  1. Inspect the body clearance.



      C316895
    1. Push the front oil pump driven gear to one side of the front oil pump body sub-assembly.

    2. Using a feeler gauge, measure the body clearance.

      Standard Clearance:
      0.12 to 0.17 mm (0.00472 to 0.00669 in.)

      Maximum Clearance:
      0.17 mm (0.00669 in.)

      If the clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear or front oil pump body sub-assembly.



  1. Inspect the side clearance.



      C316896
    1. Using a straightedge and feeler gauge, measure the side clearance of both gears.

      Standard Side Clearance:
      0.035 to 0.05 mm (0.00138 to 0.00197 in.)

      Maximum Side Clearance:
      0.05 mm (0.00197 in.)

      If the clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear or front oil pump body sub-assembly.

      HINT:
      There are 4 front oil pump drive gears and front oil pump driven gears of different thicknesses.
      Front Oil Pump Drive Gear Thickness 
      Part No.
      Mark
      Thickness
      (mm (in.))
      35321-33160
      A
      11.554 to 11.56 (0.45488 to 0.45512)
      35321-33170
      B
      11.561 to 11.567 (0.45516 to 0.45539)
      35321-33180
      C
      11.568 to 11.574 (0.45543 to 0.45567)
      35321-33190
      D
      11.575 to 11.581 (0.45571 to 0.45594)
      Front Oil Pump Driven Gear Thickness 
      Part No.
      Mark
      Thickness
      (mm (in.))
      35322-33160
      A
      11.554 to 11.56 (0.45488 to 0.45512)
      35322-33170
      B
      11.561 to 11.567 (0.45516 to 0.45539)
      35322-33180
      C
      11.568 to 11.574 (0.45543 to 0.45567)
      35322-33190
      D
      11.575 to 11.581 (0.45571 to 0.45594)



3. INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY


    C138514
  1. Using a caliper gauge, measure the inside diameter of the front oil pump body bushing.

    Standard Inside Diameter:
    43.135 to 43.160 mm (1.69822 to 1.69921 in.)

    Maximum Inside Diameter:
    43.160 mm (1.69921 in.)

    If the inside diameter is greater than the maximum, replace the front oil pump and gear body sub-assembly.



4. INSPECT STATOR SHAFT ASSEMBLY


    C138513
  1. Using a caliper gauge, measure the inside diameter of the stator shaft bushing.

    Standard Inside Diameter:
    22.500 to 22.526 mm (0.88583 to 0.88685 in.)

    Maximum Inside Diameter:
    22.526 mm (0.88685 in.)

    If the inside diameter is greater than the maximum, replace the stator shaft assembly.