Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

DTC    C1551    IG Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

The power steering ECU assembly distinguishes the ignition switch status as ON or off through the IG power source circuit.

DTC No.
DTC Detection Condition
Trouble Area
C1551
Open or short in IG power source circuit with ignition switch ON
  1. EPS-IG1 fuse
  2. IG power source circuit
  3. ECU wire sub-assembly
  4. Power steering ECU assembly

WIRING DIAGRAM


C250109E10


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly has been replaced with a new one, perform assist map writing and torque sensor zero point calibration (Click here).

HINT:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
  1. Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

    OK:
    The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.

  1. Check that the ground wire is securely installed with the bolt .

    OK:
    The ground wire is securely installed with the bolt.



NG
CONNECT CONNECTOR OR INSTALL GROUND WIRE
OK


2.READ VALUE USING INTELLIGENT TESTER
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the item "IG power supply" in the Data List and read the value displayed on the intelligent tester.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG power supply
    IG power supply/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Ignition switch ON

    OK:
    The normal condition value is displayed on the intelligent tester.



NG
Go to step 3
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
C240486E04
  1. Disconnect the Ij2 connector from the ECU wire sub-assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Ij2-5 (IG) - Body ground
    Ignition switch ON
    9 to 16 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECU Wire Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)


    C238941E05
  1. Disconnect the j2 connector from the power steering ECU assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    j2-2 (PGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY (Click here)
OK


5.CHECK ECU WIRE SUB-ASSEMBLY


    C238945E05
  1. Disconnect the j1 connector from the power steering ECU assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    j1-1 (IG) - Ij2-5 (IG)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)
    *b
    Front view of wire harness connector
    (to Vehicle Wire Harness)



NG
REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)